Automation, Inc.
™
24
TM_GF-
A
2
1
00_2200_R1A
GF-A2100
AND
GF-A2200 A
IRFLOW
M
EASUREMENT
S
TATION
Air Flow Measurement, PID Control and Alarm Solution - Analog Output
GreenTrol Automation, Inc.
•
156 Holly View Lane Loris, SC 29569
•
Toll Free: 877-4GN-TROL (877.446.8765)
•
Internet:
GreenTrol.com
Setup Menu Options (Part 2 of 3)
(Refer to Table 2 for “SI” Standard International Units of Measure)
FROM PART 1
isible only when
SYS CFG = DUAL
isible only when
SYS CFG = DUAL
isible only when
SYS CFG = DUAL
isible when ALR SRC =
FLOW, TEMP, or DELTA
isible when ALR SRC =
FLOW, TEMP, or DELTA
isible when ALR SRC =
FLOW, TEMP, or DELTA
isible only when
ALRM SRC is not disabled
isible only when
ALRM SRC is not disabled
In the following menus OUT
x
is provided for OUT
1
and OUT
separately
*ALR TYP=DEADB
Ľ
SET ALARM TYPE?
ALR SRC=TEMP1
Ľ
ALR SRC=FLOW2
Ľ
ALR SRC=TEMP2
Ľ
ALR SRC=DIFF
Ľ
ALRM DEL= 5.0S
Ľ
ALARM SETUP
Ľ
ALR SRC=TRBL
↑
Alarm source is related to the airflow/temperature sensor status
(represents sensor trouble).
Alarm source is related to FLOW1
Alarm source is related to TEMP1
*ALR DEL=5S
Ľ
SET ALR DEL?
Set Alarm ysteresis as a percentage above and below
the "ALR= " value in prior step.
ALRM= 0CFM
↑
Set flow rate or temperature to activate Alarm. (Also check ysteresis
range - see "ALRM YS= " next step.)
Set alarm relay polarity to be normally open.
Amount of time alarm condition must be present before the
alarm is activated.
SET ALRM POL?
SET ALRM YS ?
*ALR SRC=OFF
ALR TYP=DEADB
↓
ALR TYP= I
Ľ
ALR TYP=LO
↑
ALRM POL= NO
↓
ALRM YS=
15%
Ľ
*ALRM POL= NO
↑
Alarm source is related to FLOW2
Alarm source is related to TEMP2
Alarm source is related to the difference between FLOW1 and FLOW2
Deadband type alarm. Alarm when value is outside of
the setpoint
±
hysteresis
Alarm when condition is above the setpoint. Condition is cleared when
value is below the setpoint - hysteresis.
Alarm when condition is the setpoint. Condition is cleared when value is
above the setpoint
hysteresis.
ALR SRC=OFF
↓
Alarm is disabled.
SET ALARM SRC?
ALR SRC=FLOW1
Ľ
*ASP= 0CFM
Ľ
SET ALARM SP?
*ALRM YS=
15%
Ľ
ALRM POL=NC
↑
Set alarm relay polarity to be normally closed.
O
isible only when
SYS CFG = DUAL
isible only when
SYS CFG = DUAL
isible only when
SYS CFG = DUAL
In the following menus, OUT
x
is provided for OUT
1
and OUT
separately
.
TYPE=ALARM
Ľ
TYPE=DIFF
↑
TYPE=FLOW2
Ľ
TYPE=FLOW1
Ľ
TYPE=TEMP1
Ľ
TYPE=TEMP2
Ľ
*TYPE=FLOW1
Ľ
SET OUTx TYPE?
OUTx=0-5
Ľ
*OUTx=0-10
↓
SET OUTx ?
TYPE=DISABLE
↓
TYPE=CTRL
Ľ
Set the output to 0 - 5 DC
OUTx=0-10
↓
Set the output (OUT1 or OUT2) to 0 - 10 DC
OUTx SETUP
Ľ
Set the output to 2 - 10 DC
OUTx=2-10
↑
Turn the output off.
Set the output as a control signal.
Set the output to indicate the status of the alarm.
Set the output to indicate the flow signal.
Set the output to indicate the temperature signal.
Set the output to indicate the temperature signal.
Set the output to indicate the flow signal.
Set the output to indicate the difference between flow 1 and flow 2.
O
TO PART
A
B
O
Figure 15. (part 2 of 3) GF-A2100/GF-A2200 Setup Menu Option (“IP SYS”)