Greentrol Automation GF-A2100, Руководство по установке, эксплуатации и техническому обслуживанию, Страница: 21 / 28

Automation, Inc.
™
TM_GF-
A
2
1
00_2200_R1A
21
GF-A2100
AND
GF-A2200 A
IRFLOW
M
EASUREMENT
S
TATION
Air Flow Measurement, PID Control and Alarm Solution - Analog Output
GreenTrol Automation, Inc. •
156 Holly View Lane Loris, SC 29569
•
Toll Free: 877-4GN-TROL (877.446.8765)
•
Internet:
GreenTrol.com
Display Description IP Units SI Units
*AR x = Probe x duct free area (sq. ft.) where probe x is located ( x =1 or 2) 0.00 SQF 0.000 SQM
*FLOW BUF= Number of samples used to perform flow calculation (1 to 500) 10 10
*INT TIM= Time between integration updates (0.1s - 15min) 1.0S 1.0S
*ALT= Altitude for flow correction 0 ft 0 m
*FILTER x = Output x Digital Noise Filter ( x =1 or 2) 0 (off) 0 (off)
*OFF-GAIN x = Output x Offset-Gain On/Off ( x =1 or 2)
OFF OFF
*O-GMODE x = Output Offset-Gain Mode ( x =1 or 2) 1 (direct entry) 1 (direct entry)
*GAIN x = Output Gain factor ( x =1 or 2) 1.000 1.000
*OFFSET x = Output Offset factor ( x =1 or 2) 0.000 FPM 0.000 MPS
Display Description IP Units SI Units
*ALR SRC= Alarm Enable/Disable and Alarm Source selection OFF OFF
*ALR TYP= Alarm type (Deadband, Hi Limit or Low Limit) selection DEADB DEADB
*ASP= Alarm set point value selection 0 CFM 0 LPS
*ALRM HYS =
Alarm Hysteresis (range in percentage) above and below the *ASP value
that results in alarm activation.
15% 15%
*ADEL =
Alarm Delay sets the time period that the Alarm condition must be
present before the Alarm is activated.
5S 5S
*ALRM POL =
Alarm relay contact configuration
(NO for normally open or NC for normally closed)
NO NO
Display Description IP Units SI Units
*LL= Analog Output Low limit cutoff 0 CFM 0 LPS
*MS= Analog Output Minimum Scale for Temperature -20 F -20 C
*SETP= PID Set Point flow value 0 CFM 0 LPS
*INTRVL= PID Update interval (seconds) 1.0s 1.0s
*ACTION=
Set PID control action:
Direct=Measurement and PID control are directly proportional
Reverse=Measurement and PID control are inversely proportional
Direct Direct
*DEADB= Deadband range (expressed as a percentage of *SETP= value) 10% 10%
*ON DEL= Delay after power-up before the PID control output is active 30.0s 30.0s
*DIVISR= PID Gain Divisor 1000 1000
*P GAIN= Proportional gain term 10 10
*I GAIN= Integral gain term 1 1
*D GAIN= Derivative gain term 0 0
*MAX INT= Maximum value for Integral state 20% 20%
*OUT x = Analog output x signal range ( x =1 or 2)
0-10VDC
FLOW1
FLOW1
*FS= Analog Output full scale value
5,000 CFM 25 LPS
*CTRL=
Sets Control Loop strategy; to follow flow output 1 flow, output 2 flow or
the flow difference between them
FLOW1 FLOW1
SYSTEM SETUP SUB-MENU
OUTPUT x SETUP SUB-MENU ( x =1 or 2)
ALARM SETUP SUB-MENU
0-10VDC
*TYPE= Analog output 1 and 2 Type (sets configuration of Analog Outputs)
Table 3. Factory Default Setup Menu Values