background image

2

Ceiling Exhaust and Inline Fans

B Model

A Model

Prepare the fan

Airflow

Airflow

Access 

Panel

Access

Panel

Knockouts

Electrical

Access

Panel

Power Assembly

If power assembly (motor, wheel, and scroll) is not 
installed in housing, insert the electrical plug into fan 
socket, then slide scroll end of power assembly into 
fan housing. Attach by using two sheet metal screws 
provided.

Ductwork

 

Check ductwork to see if the fan’s discharge requires 
rotation from horizontal to vertical discharge.

Fan Rotation

To rotate from horizontal to vertical discharge
A-Models Only

A-50-500, 710, 780 Models

Remove the two screws holding the power assembly 
in and pull power assembly out. Rotate power 
assembly 180 degrees and put back into fan. Use 
the same screws to reattach power assembly to fan 
housing. Flip fan over and remove the four screws 
holding the discharge duct and damper assembly. 
Exchange the assembly with plate mounted on top of 
fan, as shown in these illustrations.

Remove Wiring Knockout

Remove either top or side wiring knockout, 
depending on wiring  
direction, by  
bending it back  
and forth to  
break tabs.

A-700, 900-1500 Models

Remove the eight screws 
holding the access panel or 
collar as shown in picture. 
Rotate the fan housing so 
the discharge is facing up. 
Replace access panel or 
collar and screws.

®

Содержание CSP









Отзывы: