background image

7

Ceiling Exhaust and Inline Fans

SP/CSP models shown are 
UL and cUL listed E 33599 

Other Installation Considerations

Ductwork and Noise

Fiberglass ductboard is a better choice than metal 
ductwork for reducing fan noise and is highly 
recommended for low sound applications. Where metal 
duct is used, sound transmission can be reduced with 
flexible duct connections between the fan and the duct.

Sound and Location

The location of these fans must be taken into 
consideration before installation. In critical sound 
installations, insulated ductwork, flexible duct 
connections or placing the fan in a remote section of 
ductwork are solutions to meeting the required fan sound 
levels.

Filters

The addition of an intake filter is highly recommended 
for these fans, even in clean air environments excess 
dirt can accumulate on wheels and motors causing 
reduced performance and imbalance.

Filters, once installed, should be checked and cleaned 
periodically to maintain performance.

Greenheck offers washable aluminum mesh filters 
specifically designed for these fans. Please consult our 
SP/CSP catalog for more information.

Flex Duct
Connections

Fiberglass
Ductboard

Remote
Mounted

Correct Low
Sound Installation

Incorrect

SP and SP-C
Mounted Directly
Overhead

CSP and SP-C
Converted
to Inline

General Maintenance Suggestions

Model SP/CSP ceiling exhaust fans require very little maintenance. But since small problems over time left 
unchecked could lead to loss of performance or early motor failure, we do recommend that the unit be inspected 
periodically (once or twice a year).

The fan motor and wheel should be checked for dust and dirt accumulations. Dirt buildup can lead to loss of 
performance and motor overheating. Cleaning can be accomplished by brushing off any dust that may have 
accumulated. Even filtered units can accumulate build-up and should be checked when cleaning filters.

The motor should be checked for lubrication at this time. Lubricate only those motors which have an oil hole 
provided. A few drops of all purpose oil (SAE 20) will be sufficient.

®

Содержание CSP









Отзывы: