70
Technical Information
Service Manual
TURBO
button
Under COOL or HEAT mode, press this button to turn to quick
COOL or quick HEAT mode. " " icon is displayed on remote
controller. Press this button again to exit turbo function and "
" icon will disappear. If start this function, the unit will run at
super-high fan speed to cool or heat quickly so that the ambient
temperature approaches the preset temperature as soon as
possible.
/
button
●
Press " " or " " button once increase or d ecrease set
temperature 1°C (°F). Holding " " or " " button, 2s later,
set temperature on remote controller will change quickly. On
releasing button after setting is finished, temperature indicator on
indoor unit will change accordingly. (Temperature can't be
adjusted under auto mode)
●
When setting T-ON, T-OFF or CLOCK, press " " or " " button
to adjust time. (Refer to CLOCK, TON,T-OFF buttons)
button
Press this button can select left & right swing angle. Fan blow
angle can be selected circularly as below:
Note:
● Press this button continuously more than 2s, the main unit will
swing back and forth from left to right, and then loosen the button,
the unit will stop swinging and present position of guide louver
will be kept immediately.
● Under left and right swing mode, when the status is switched
from off to
, if press this button again 2s later,
status
will switch to off status directly; if press this button again within
2s, the change of swing status will also depend on the circulation
sequence stated above.
● The function is only available for some models.
button
Press this button can select left & right swing angle. Fan blow
angle can be selected circularly as below:
no display
(horizontal louvers stops
at current position)
●
When selecting " ", air conditioner is blowing fan
automatically. Horizontal louver will automatically swing up &
down at maximum angle.
●
When selecting "
、
、
、
、
", air conditioner is blowing fan
at fixed position. Horizontal louver will stop at the fixed position.
●
When selecting "
、
、
", air conditioner is blowing fan at
fixed angle. Horizontal louver will send air at the fixed angle.
●
Hold " "button above 2s to set your required swing angle.
When reaching your required angle, release the button.
Note:
● "
、
、
" may not be available. When air conditioner
receives this signal, the air conditioner will blow fan automatically.
● Press this button continuously for more than 2s, the main
unit will swing back and forth from up to down, and then loosen
the button, the unit present position of guide louver will be kept
immediately.
● Under up and down swing mode, when the status is switched
from off to , if press this button again 2s later, status will
switch to off status directly; if press this button again within 2s,
the change of swing status will also depend on the circulation
sequence stated above.
T-ON T-OFF
button
● T-ON button
"T-ON" button can set the time for timer on. After pressing this
button, " " icon disappears and the word "ON" on remote
controller blinks. Press "▲" or " ▼ " button to adjust T-ON
setting. After each pressing "▲" or " ▼ " button, T-ON setting will
increase or decrease 1min. Hold "▲" or " ▼ " button, 2s later, the
time will change quickly until reaching your required time. Press
"T-ON" to confirm it. The word "ON" will stop blinking. "
" icon
resumes displaying. Cancel T-ON: Unde the condition that T-ON
is started up, press "T-ON " button to cancel it.
● T-OFF button
"T-OFF" button can set the time for timer off. After pressing this
button, " " icon disappears and the word "OFF" on remote
controller blinks. Press "▲" or " ▼ " button to adjust T-OFF
setting. After each pressing "▲" or " ▼ " button, T-OFF setting
will increase or decrease 1min. Hold "▲" or " ▼ " button, 2s later,
the time will change quickly until reaching your required time.
Press "T-OFF" word "OFF" will stop blinking. " " icon resumes
displaying. Cancel T-OFF. Under the condition that T-OFF is
started up, press "T-OFF" button to cancel it.
Note:
● Under on and off status, you can set T-OFF or T-ON
simultaneously.
● Before setting T-ON or T-OFF, please adjust the clock time.
● After starting up T-ON or T-OFF,set the constant circulating
valid.After that, air conditioner will be turned on or turned off
according to setting time.ON/OFF button has no effect on setting.
If you don’t need this function, please use remote controller to
cancel it.
I FEEL
button
Press this button to start I FEEL function and " " will be
displayed on the remote controller. After this function is set, the
remote controller will send the detected ambient temperature
to the controller and the unit will automatically adjust the indoor
temperature according to the detected temperature. Press this
button again to cancel I FEEL function and " " will disappear.
● Please put the remote controller near user when this function
