61
Technical Information
Service Manual
hea t mode. Press "▲" o r "▼" button to adjust set temperature.
Press "FAN" button to adjust fan speed. Press " " / " " button
to adjust fan blowing angle.
NOTE:
●
For preventing cold air, after start ing up heat mode, indoor unit
will delay 1~5 minutes to blow air (Actual delay time depends on
indoor ambient temperature).
●
Set temperature range from remote controller: 16~30°C(61-
86°F).
●
Fan speed: auto, low speed, low-medium speed,medium speed,
medium-high speed,high speed.
●
Under auto mo de, temperature can be d isplayed; Under auto
mode, set temperature can be adjusted.
button
This button is used for setting Fan Speed in the sequence that
goes from AUTO, , ,
,
,
, then back to Auto.
NOTE:
● It's low fan speed under dry mode.
● X-FAN function Hold fan speed button for 2s in cool or dry
mode, the icon " " is displayed and the indoor fan will continue
operation for a few minutes in order to dry the indoor unit even
though you have turned off the unit. Af ter energization, X-FAN
OFF is defaulted. X-FAN is not available in auto, fan or heat mode.
This function indicates that moisture on evaporator of indoor unit
will be blowed after the unit is stopped to avoid mould.
● Having set X-FAN function on: After turning off the unit by
pressing " " button indoor fan will continue running for a few
minutes. at low speed. In this period, Hold fan speed button for 2s
to stop indoor fan directly.
● Having set X-FAN function off: After turning off the unit by
pressing " " button, the complete unit will be off directly.
button
Under cool or heat mode, press this button to turn to quick cool
or quick heat mode. " " icon is displayed on remote controller.
Press this button again to exit t urbo function and " " icon will
disappear.
If start this function, the unit will run at super-high fan speed to
cool or heat quickly so that the ambient temperature approaches
the preset temperature as soon as possible.
button
Press "▲" or "▼" button once increase or decrease set
temperature 1°C(°F). Holding "▲" or "▼" button, 2s later, set
temperature on remote controller will change quickly. On releasing
button after setting is finished, temperature indicator on indoor
unit will change accordingly.
When setting TIMER ON, TIMER OFF or CLOCK, press "▲" or
"▼" button to adjust time. (Refer to CLOCK, TIMER ON, TIMER
OFF buttons).
button
Press this button can select left & right swing angle. Fan blow
angle can be selected circularly as below:
NOTE:
● Press this button continuously more than 2s, the main unit will
swing back and forth from left to right, and then loosen the button,
the unit will stop swinging and present position of guide louver will
be kept immediately.
● Under left and right swing mode, when the status is switched
from off to , if press this button again 2s later, status will switch to
off status directly; if press this button again within 2s, the change
of swing status will also depend on the circulation sequence
stated above.
● The function is only available for some models.
button
Press this button can select up & down swing angle. Fan blow
angle can be selected circularly as below:
●
When selecting " ", air conditioner is blowing fan automatically.
Horizontal louver will automatically swing up & down at maximum
angle.
●
When selecting "
", air conditioner is blowing fan
at fixed position. Horizontal louver will stop at the fixed position.
●
When selecting "
", air conditioner is blowing fan at
fixed angle. Horizontal louver will send air at the fixed angle.
●
Hold " " button above 2s to set your required swing angle.
When reaching your required angle, release the button.
NOTE:
●
“
" may not be available. When air condi - tioner
receives this signal, the air conditioner will blow fan automatically.
●
Press this button continuously for more than 2s, the main
unit will swing back and forth from up to down, and then loosen
the button, the unit present position of guide louver will be kept
immediately.
●
Under up and down swing mode, when the status is switched
from off to , if press this button again 2s later, status will switch to
off status directly; if press this button again within 2s, the change
of swing status will also depend on the circu lation sequence
stated above.
