background image

U-Match Series Duct Type Unit 

WARNING

 

(11) The air conditioner can be cleaned only after it is turned off and 

power-disconnected, otherwise electric shock may occur. 

(12) The air  conditioner is not intended to be cleaned or maintained by children 

without supervision. 

(13) Do not alter the setting of pressure sensor or other protective devices. If the 

protective devices are short-circuited or changed against rules, fire hazard or 

even explosion may occur. 

(14) Do not operate the air conditioner with wet hands. Do not wash or sprinkle 

water on the air conditioner, otherwise malfunction or electric shock will occur. 

(15) Do not dry the filter with naked flame or an air blower; otherwise the filter will be 

out of shape. 

(16) If the unit is to be installed in a small space, please adopt protective measures 

to prevent the concentration of refrigerant from exceeding the allowable safety 

limit; excessive refrigerant leakage may lead to explosion. 

(17) When installing or re-installing the air conditioner, please keep the refrigerant 

circuit away from substances other than the specified refrigerant, such as air. 

Any presence of foreign substances will cause abnormal pressure change or 

even explosion, resulting in injury. 

 

NOTICE

 

(1)  Do not put a finger or other objects into the air inlet or air return grill. 
(2)  Please adopt safety protection measures before touching the refrigerant pipe; 

otherwise your hands may be hurt. 

(3)  Please arrange the drain pipe according to the instruction manual. 
(4)  Never stop the air conditioner by directly cutting off the power. 
(5)  Please select the proper copper pipe according to the requirement for pipe 

thickness. 

(6)  Indoor unit can only be installed indoors while outdoor unit can be installed 

either indoors or outdoors. Never install the air conditioner in the following 

places: 

a)  Places with oil smoke or volatile liquid: plastic parts may deteriorate and 

fall off or even cause water leakage. 

b)  Places with corrosive gas: copper pipe or the welding  parts may be 

corroded and cause refrigerant leakage. 

(7)  Adopt proper measures to protect the outdoor unit from small animals because 

they may damage the electric components and cause malfunction of the air 

conditioner. 

 

Содержание U-Match GU100W/A1-M





















































Отзывы: