Gree U-Match GU100W/A1-M страница 49 Скачать руководство пользователя

Страница: 49 / 52

U-Match Series Duct Type Unit

5.2 Error Code

WARNING

①

If abnormal things (for example, awful smell) occur, please stop the unit

immediately and disconnect power. Then contact Gree’s authorized service

center. If the unit continues to run in abnormal situations, it may get damaged

and cause electric shock or fire hazard.

②

Do not repair the air conditioner by yourself. Improper maintenance will cause

electric shock or fire hazard. Please contact Gree’s authorized service center

and send for professional service staff to repair.

If the display panel or wired control displays an error code, please

refer to the error code meaning stated in the following table.

Number

Error code Error

Compressor high pressure protection

Indoor anti-freeze protection

Compressor low pressure protection, refrigerant lack

protection and refrigerant colleting mode

Compressor air discharge high-temperature protection

Communication error

Indoor fan error

Water-full protection

Indoor ambient temperature sensor error

Evaporator temperature sensor error

Condenser temperature sensor error

Outdoor ambient temperature sensor error

Discharge temperature sensor error

Wired control temperature sensor error

IDU jumper cap error

IDU or ODU memory chip error

Electric box sensor error

Compressor overload protection

Overload

ODU jumper cap error

Emergency Stop(Fire Alarm)

Содержание U-Match GU100W/A1-M





















































Результаты поиска

Содержание U-Match GU100W/A1-M

Отзывы:

Похожие инструкции для U-Match GU100W/A1-M

Бренды по названию

Популярные бренды

Gree U-Match GU100W/A1-M, Руководство пользователя

Результаты поиска

Содержание U-Match GU100W/A1-M

Отзывы:

Похожие инструкции для U-Match GU100W/A1-M

Бренды по названию

Популярные бренды