Gree GWC09MB-D3DNK Series, Руководство пользователя

Страница: 26 / 38

22
Fait es u ne rec om man dat ion su r l'e mpla cem ent idé al a u cl ien t p uis vali dez av ec l e cl ien t.
1. Acc roc hez le su ppo rt m ura l a u m ur; à l'a ide du ni vea u, a jus tez l'a ngl e
hor izo nta l, p uis mar que z le s tr ous de vis su r le m ur.
2. À l'a ide de la pe rçe use à per cus sio n, p erc er d es tro us de vis dan s le
mur (la gr oss eur de la tê te à p erç age do it ê tre la m êm e q ue la che ville
de pla stiq ue) , p uis ent rez la ch evil le dan s le tro u.
3. Fixe z le su ppo rt m ura l à l'a ide de s v is aut o-ta rau deu ses
(ST 4.2 X25 TA) . E nsu ite , a ssu rez -vo us que le su ppo rt e st b ien an cré en
tira nt d ess us. Si la ch evil le en pla stiq ue se rel âch e, p erc er u n a utre tro u
de vis tou t à cô té.
1. Cho isir l'e mpl ace men t d u tr ou pou r la tu yau ter ie pou r q u'il soi t e n lig ne
ave c le tu yau de so rtie . L e tr ou pou r la tu yau ter ie doi t ê tre pl us bas qu e
le sup por t m ura l, t el q u'ill ust ré ci-a prè s.
2. Fai tes un e o uve rtu re pou r la tu yau ter ie de ⏀ 55 ou ⏀ 70 sur le tu yau de
sor tie sé lec tio nné . P our as sur er u n d rai nag e e ffic ace , fa ite s u n tr ou
ave c u ne lég ère pe nte de 5 -10 ° v ers le ba s e t v ers l'e xté rie ur.
22
Mur
Mar que r le m ilie u
Nive au
Rig ht
Rig ht
Mur
Ins tal lat ion de l'u nité in tér ieu re
Éta pe 1: c hoi sir l'em pla cem ent
Éta pe 3: p erc er u n tr ou pou r le s tu yau x
Éta pe
2: i nst alla tio n d u s upp ort mur al
Dista nce
du m ur
150 mm
Dista nce
du m ur
150 mm
Dista nce
du m ur
150 mm
Gau che
Gau che
Tro u a rriè re pou r la tu yau ter ie Tro u a rriè re pou r la tu yau ter ie
Tro u a rriè re pou r la tu yau ter ie
Tro u a rriè re pou r la tu yau ter ie
18K:
Φ55mm Φ55mm
24K:
Φ70mm Φ70mm
09
、
12K:
Φ55/Φ70 Φ55/Φ70
Space
to the
wall
above
150mm
Space
to the
wall
above
150mm
Wall
(Rear pipping hole) ( Rear pipping hole)
Wall
Installation of indoor unit
Step Three: open piping hole
Step Two: install wall-mounting frame
Step One: choosing installation location
Recommend the installation location to the client and then confirm it with the client.
1. Hang the wall-mounting frame on the wall; adjust it in horizontal position
with the level meter and then point out the screw fixing holes on the
wall.
2. Drill the screw fixing holes on the wall with the impact drill (the specifica-
tion of drill head should be the same as the plastic expansion particle)
and then fill the plastic expansion particles in the holes.
3. Fix the wall-mounting frame on the wall with tapping screws
(ST4.2X25TA) and then check if the frame is firmly installed by pulling
the frame. If the plastic expansion particle is loose, please drill another
fixing hole nearby.
1. Choose the position of piping hole according to the direction of outlet
pipe. The position of piping hole should be a little lower than the wall-
mounted frame, shown as below.
2. Open a piping hole with the diameter of ⏀ 55 or ⏀ 70 on the selected
outlet pipe position.ln order to drain smoothly, slant the piping hole on
the wall slightly downward to the outdoor side with the gradient of 5-10°.
Mark in the middle of it Mark in the middle of it
level meter
level meter
level meter
18K:
Φ55 mm Φ55 mm
24K:
Φ70mm Φ70 mm
09
、
12K:
Φ55 /Φ 70 Φ55 /Φ 70
Mur
Mar que r le m ilie u
Nive au
Mur
Dista nce
du m ur
150 mm
Gau che
Tro u a rriè re pou r la tu yau ter ie
Tro u a rriè re pou r la tu yau ter ie
Rig ht
Dista nce
du m ur
150 mm
Mur
Mur
Mar que r le m ilie u
Nive au
Dista nce
du m ur
150 mm
Wall
Left
Right
Wall
Space
to the
wall
above
150mm
Space
to the
wall
above
150mm
Left
Right
(Rear pipping hole) (Rear pipping hole)
Mark in the middle of it
Space
to the
wall
above
150mm
Space
to the
wall
above
150mm
Wall
Wall
Left
Right
(Rear pipping hole)
(Rear pipping hole)
00762_BUILDER 15SEER 9K12K18K24K_Mise en page 1 16-06-02 14:49 Page26