Gree GMV-ND24A/A-T Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 22

Gree GMV-ND24A/A-T Скачать руководство пользователя страница 17

GMV DC Inverter VRF

14

Fig 5.3.1 Fig 5.3.2

(4) Fix the communication cable with clamp of electric box.

(5) For more reliable communication, make sure connect the terminal resistor to the

most downstream IDU of the communication bus (terminal D1 and D2), as shown in

fig 5.3.2, terminal resistor is provided with each ODU.

5.4 Connect Communication Wire of Wired Controller

(1) Open electric box cover of indoor unit.

(2) Let the communication wire go through the rubber ring.

(3) Connect the communication wire to terminal H1 and H2 of indoor 4-bit wiring board.

(4) Fix the communication wire with wire clip on the electric box.

(5) Wiring instructions of remote receiving light board and wired controller:

1) Fig 5.4.1 shows the installation of wired controller.

Fig 5.4.1

2) Wired controller and receiving light board can be installed at the same time. When

operating through a remote controller, both wired controller and the receiving light

board can receive the signals.

«
...
15
16
17
18
19
...
»

Содержание GMV-ND24A/A-T























Отзывы:

Нет отзывов