Gree DUCT09HP230V1BD Скачать руководство пользователя страница 22

Страница: 22 / 24

Multi Variable Air Conditioners Ducted Type Indoor Unit

(4) Check if any error code displayed after energized.

7.3 Maintenance after the Seasonal Use

(1)

Set the unit in fan mode for half a day

a sunny day to dry the in

nal

part of unit;

(2)

When the unit won’t be

being

used for a long time,

disconnect the

power supply

to save

energy;

he characters on the wired controller screen will disappear after cutting off the

power

supply.

8 Table of Error Codes for Indoor Unit

Number

Error code

Error

Compressor high pressure protection

Indoor anti-freeze protection

Low pressure c

ompressor protection,

low

refrigerant

protection and refrigerant colle

ting mode

Compressor high discharge temperature protection

Communication error

Full water protection

Indoor ambient temperature sensor is open/short circuited

Indoor evaporator temperature sensor is open/short

circuited

Outdoor ambient temperature sensor is open/short

circuited

Outdoor condenser temperature sensor is open/short

circuited

Outdoor discharge temperature sensor is open/short

circuited

Loading EEPROM malfunction

Anti-high temperature protection

No feedback

from

indoor fan motor

Zero-crossing protection

Jumper cap malfunction protection

AC over-current protection

Mode conflict

Note: If there’re other error codes, please contact qualified professionals for service.

Содержание DUCT09HP230V1BD

























Результаты поиска

Содержание DUCT09HP230V1BD

Отзывы:

Похожие инструкции для DUCT09HP230V1BD

Бренды по названию

Популярные бренды

Gree DUCT09HP230V1BD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DUCT09HP230V1BD

Отзывы:

Похожие инструкции для DUCT09HP230V1BD

Бренды по названию

Популярные бренды