background image

  Drill bits: 1/16" [1.6mm], 5/64" [2mm], 1/8" [3.2mm]

  Panel line pen (TOPQ2510)

  Rotary tool such as Dremel

®

  Rotary tool reinforced cut-off wheel (GPMR8020)

 AccuThrow

 defl ection gauge (GPMR2405)

 Hobbico

®

 pin vise 1/16" collet w/6 bits (HCAR0696)

  Hobbico 7-piece ball tip hex L-wrench

 metric 

(HCAR0521)

  Great Planes clevis installation tool (GPMR8030)

…And If You Really Want to Go Nuts

  Cooler fi lled with ice and soda

 Folding table

 Lawn chairs

  EZ-up or canopy for shelter

 First-aid kit

 Paper towels

  Spray-on glass cleaner

 Sunglasses

 Sun block

IMPORTANT BUILDING NOTES

•  When you see the term test fi t in the instructions, it 
means that you should fi rst position the part on the assembly 
without using any glue, then slightly modify or custom fi t 
the part as necessary for the best fi t.

•  Whenever the term glue is written you should rely upon 
your experience to decide what type of glue to use. When 
a specifi c type of adhesive works best for that step, the 
instructions will make a recommendation.

• Whenever 

just 

epoxy is specifi ed you may use either 

30-minute (or 45-minute) epoxy or 6-minute epoxy. When 
30-minute epoxy is specifi ed it is highly recommended that 
you use only 30-minute (or 45-minute) epoxy, because you 
will need the working time and/or the additional strength.

•  Photos and sketches are placed before the step they 
refer to. Frequently you can study photos in following steps 
to get another view of the same parts.

•  The ElectroStik EP ARF is factory-covered with Top Flite 
MonoKote fi lm. Should repairs ever be required, MonoKote 
can be patched with additional MonoKote purchased 
separately. MonoKote is packaged in six-foot rolls, but 
some hobby shops also sell it by the foot. If only a small 
piece of MonoKote is needed for a minor patch, perhaps a 
fellow modeler would give you some. MonoKote is applied 
with a model airplane covering iron, but in an emergency a 
regular iron could be used. A roll of MonoKote includes full 
instructions for application. Following are the colors used on 
this model and order numbers for six foot rolls.

 

Missle Red – TOPQ0201

 Jet 

White 

– 

TOPQ0204

•  The stabilizer and wing incidences and motor thrust 
angles have been factory-built into this model. However, 
some technically-minded modelers may wish to check these 
measurements anyway. To view this information, visit the web 
site at www.greatplanes.com and click on “Technical Data.” 
Due to manufacturing tolerances which will have little or no 
effect on the way your model will fl y, please expect slight 
deviations between your model and the published values.

ORDERING REPLACEMENT PARTS

Replacement parts for the Great Planes ElectroStik EP ARF are 
available using the order numbers in the Replacement Parts 
List
 that follows. The fastest, most economical service can be 
provided by your hobby dealer or mail-order company. 

To locate a hobby dealer, visit the Hobbico web site at 
www.hobbico.com. Choose “Where to Buy” at the bottom of the 
menu on the left side of the page. Follow the instructions provided 
on the page to locate a U.S., Canadian or International dealer. 

Parts may also be ordered directly from Hobby Services by 
calling (217) 398-0007, or via facsimile at (217) 398-7721, but 
full retail prices and shipping and handling charges will apply. 
Illinois and Nevada residents will also be charged sales tax. If 
ordering via fax, include a Visa

®

 or MasterCard

®

 number and 

expiration date for payment. Mail parts orders and payments by 
personal check to:

Hobby Services

3002 N. Apollo Drive, Suite 1

Champaign, IL 61822

Be certain to specify the order number exactly as listed in the 
Replacement Parts List. Payment by credit card or personal 
check only; no C.O.D. 

If additional assistance is required for any reason, contact Product 
Support by e-mail at [email protected], or 
by telephone at (217) 398-8970. 

Replacement Parts List 

Description 

How to Purchase

Missing pieces 

Contact Product Support

Instruction manual 

Contact Product Support

Full-size plans 

Not available

Contact your hobby supplier for the following parts:

GPMA3300 Wing 

Set

GPMA3301 Fuselage
GPMA3302 Tail 

Set

GPMA3303 Landing 

Gear

GPMA3304 Tail 

Wheel

GPMA3305 

Carbon Fiber Wing Joiner Tube

GPMQ4404 

10-24 Nylon EZ Bolts

GPMQ4273 

4mm Low Profi le Landing Gear Axles

4

Содержание ElectroStik ARF





















Отзывы: