manualshive.com logo in svg

Great Dane Chariot / Chariot LX GDRZ48-17KAE, Руководство оператора, Страница: 66 / 76

Поделиться
Скачать
Great Dane Chariot / Chariot LX GDRZ48-17KAE Скачать руководство пользователя страница 66

Troubleshooting - 62

TROUBLESHOOTING

Machine

Park Brake

Steering

Starter Turns Slowly

Loose or corroded battery or ground connections.

Low battery power - charge battery.

Engine oil viscosity too heavy.

Hydraulic pump linkages failed and are engaged.

If

Check

Excessive Machine Vibration

Engine speed too slow.

Machine Will Not Move With Engine Running

Park brake locked.

Transmission hydraulic oil level low.

Transmission oil cold - allow engine to warm.

Traction drive belt slipping.

Hydraulic pump free-wheel valves open.

Traction drive belt damaged or worn.

Hydrostatic pump and/or wheel motor problems. See your Great 
Dane servicing dealer.

Machine Creeps With Engine Running and Motion 
Control Levers in a Neutral Position

Needs shift control linkage adjustment.

If

Check

Park Brake Not Working Correctly

Brakes out of adjustment - adjust linkage.

Brake drums wet.

Worn brake shoes.

Brake cables damaged.

If

Check

Steering Not Working

Park brake locked.

Hydraulic pump free-wheel valves partially open.

Improper tire Inflation.

Hydrostatic transmission oil low.

Traction drive belt slipping.

Traction drive belt damaged or worn.

Machine Will Not Follow a Straight Path

Steering tracking out of adjustment.

If

Check

Содержание Chariot / Chariot LX GDRZ48-17KAE













































































Отзывы:

Нет отзывов