manualshive.com logo in svg

Great Dane Chariot / Chariot LX GDRZ48-17KAE, Руководство оператора, Страница: 28 / 76

Поделиться
Скачать
Great Dane Chariot / Chariot LX GDRZ48-17KAE Скачать руководство пользователя страница 28

Service Lubrication - 24

SERVICE LUBRICATION

Service Lubrication

Grease

Use a general all-purpose grease with an NLGI grade No. 2 
rating.

Wet or high-speed conditions may require use of a special-
use grease. Contact your servicing dealer for information.

Spray Lubricant

Use a general-purpose petroleum-based spray lubricant.

Lubrication Points

MX15286

•

Chariot LX only: Grease caster wheel bearings (A).

•

Grease caster wheel spindle bearings (B).

MX15289

•

Grease HOC shafts (C) (two points on each side of the 

machine).

MX15319

•

Grease mower deck thrust arms (D), located at the rear 

of the mower deck.

MX15287

•

Apply grease to three spindle bearings (E), until grease 

is expelled from vent (F) on spindle housings.

MX15320

•

Grease traction drive belt tension arm pivot (G).

IMPORTANT: Avoid damage! If operating outside 
that temperature range, contact your servicing 
dealer for a special-use grease.

A

B

C

D

F

E

G

Содержание Chariot / Chariot LX GDRZ48-17KAE













































































Отзывы:

Нет отзывов