
24
40 cm
160
cm
CH1
PM
(9+9)
CH2
PM
PM
(9+9)
SG
15
cm
15cm
7
TT
Fitting the wall plate (CH) to the wall (M):Only for oval pools.
Using a clamp (SG) hold the wall plate to the end of the wall and fit the bushing (PM) at a distance of 15 cm from the top and 15
cm from the end of the wall. Use a metal bit with a diameter of 11-12 mm and a cement bit with a diameter of 8 mm to drill the wall
plate and the wall. Apply rustproof paint in the holes using a brush.
Place 9 bushings along the entire wall surface in lines of three from top to bottom with a distance of 40 cm between them vertically
and a distance of 160 cm horizontally. Fit them in place using a hammer.
Very important: once the first column of bushings have been fitted, stretch the wall plate to ensure that it is flush to the wall before
fitting the second column of bushings. When all the bushings have been fitted and the first piece of wall plate is in position, fit it
to the second piece of wall plate using the wall plate fastening screws (TT). Swimming pool earth connection (see page 28).
To fit the second piece of wall plate, proceed as indicated for the first piece.
Once the entire perimeter of the swimming pool has been fitted, place the top extruded section pieces on the top of the wall plate.
First fit the straight section pieces and then the curved section pieces. If the top track formed with the top section pieces is too
long, cut the last top section piece down to the necessary size.
NOTE: We recommend you cover each bushing with adhesive tape to protect the liner during
installation. Also cover the perforation marks that are not to be used.
DK
Tool necessary (not included)
Nødvendigt værktøj (medfølger ikke)
Tarvittava työkalu (ei mukana)
Nødvendig verktøy (medfølger ikke)
Verktyg behövs (ingår ej)
Montering af vægpladen (CH) til væggen (M): kun for ovale pools.
Ved hjælp af en klemme (SG) holdes vægpladen fast til enden af væggen, og bøsningen (PM) fastgøres i en afstand af 15 cm
fra toppen og 15 cm fra enden af væggen. Bruge et metalbor med en diameter på 11-12 mm og et cementbor med en diameter
på 8 mm til at bore huller i vægpladen og væggen med. Påfør rustbeskyttende maling i hullerne ved hjælp af en pensel.
Anbring 9 bøsninger langs hele vægoverfladen i rækker med tre fra top til bund med en lodret afstand på 40 cm og en vandret
afstand på 160 cm. Fastgør dem ved hjælp af en hammer.
Meget vigtigt: når den første kolonne af bøsninger er monteret, skal vægpladen strækkes for at sikre, at den flugter med
væggen inden montering af den anden kolonne af bøsninger. Når alle bøsninger er monteret, og det første stykke vægplade er
på plads, skal det tilpasses det andet stykke vægplade ved hjælp af fastgørelsesskruerne til vægpladen (TT). Jordforbindelse
af poolen (se side 28).
For at tilpasse det andet stykke vægplade skal du fortsætte som beskrevet for det første stykke.
Når hele omkredsen af swimmingpoolen er monteret, skal du anbringe de øverste ekstruderede sektionsstykker øverst på
vægpladen.
Monter først de lige stykker og derefter de buede stykker. Hvis det øverste spor bestående af de øverste sektionsstykker er for
langt, skal det sidste af de øverste sektionsstykker beskæres til den nødvendige størrelse.
BEMÆRK: Vi anbefaler, at du dækker hver bøsning med tape for at beskytte dugen under installationen. Dæk også
perforeringsmærkerne, der ikke skal anvendes.