
PHOTO 6-2:
Fitting the wall plate (CH) to the wall (1 piece) PEOV7027 - PEOV6027 - PEOV5027 - PEOV7059 - PEOV6059 - PEOV505
Working clockwise, fit the end into place so that the skimmer cut-out is at the middle of one of the curved parts
When fitting the wall plate, choose the location for the skimmer taking into account the main wind direction to help the flow towards the skimmer.
Position the start of wall plate CH1 40 cm from one of the ends of the wall (M) so that the mouth of the skimmer will be at the middle of one of the
curved parts, and the perforation mark for the lamps and the pool cleaner valve are accessible and not covered by the walls. Fit all the bottom
track guide section pieces and slide the wall plate into the groove.
PHOTO 6-1:
Fitting the wall plate (CH) to the wall (2 pieces) PEOV9159 - PEOV8059 - PEOV9127 - PEOV8027
The pool perimeter comprises two wall plates of the same length to make handling easier, since in one single piece, it is too heavy.
First of all, fit the wall plate with the perforation for the skimmer (SKIMMER label).
One of the wall plates has a perforation mark for the mouth of the skimmer (CH1) and the other piece (CH2) has a perforation mark for the return
or discharge valves (VR). When fitting the wall plate, choose the location for the skimmer taking into account the main wind direction to help the
flow towards the skimmer.
Fit all the bottom track guide section pieces and slide the wall plate into the groove.
IMPORTANT: If the bottom section-pieces need to be cut, half the amount to be cut off must be cut from each half-circle. BEFORE CUTTING, CHECK THAT THE
WALL PLATING IS SLOTTED INTO THE GROOVES IN THE SECTION-PIECES IN THE CURVED PART ALL AROUND THE POOL AND PROPERLY FITTED
AGAINST THE METAL BRACKETS IN THE STRAIGHT PART.
Position the start of wall plate CH1 40 cm from one of the ends of the wall (M) so that the perforation mark for the lamps and the pool cleaner
valve are accessible and not covered by the walls.
NOTE: The other end of the wall plate CH1 must also be 40 cm from the wall on the other side.
VERY IMPORTANT: Before fitting the wall plate to the wall, CHECK said measurements (40 cm)
at both ends. Make sure you do the same before fitting the second wall plate CH2. If these measurements are not adhered to, the two semicircles
will not be equal and you will not be able to continue the installation.
22
SKIMMER
CH2
VL
M
P
VR
40
cm
CH1
SKIMMER
40
cm
6 - 1
U2
BEDDING - UNDERLAG - ALUSTA
FUNDAMENT - BÄDD
WALL PLATE JOINT
VÆGPLADESAMLING
SEINÄLEVYN LIITOS
VEGGPLATESKJØT
FOG, VÄGGPLATTA
WALL PLATE JOINT - VÆGPLADESAMLING
SEINÄLEVYN LIITOS - VEGGPLATESKJØT
FOG, VÄGGPLATTA
U1
VR
DK
FOTO 6-2:
Montering af vægpladen (CH) til væggen (1 stykke) PEOV7027 - PEOV6027 - PEOV5027 - PEOV7059 - PEOV6059 - PEOV505
Monter enden, så udskæringen til afløbet befinder sig midt i en af de buede sektioner. Fortsæt monteringen i urets retning.
Når vægpladen monteres, skal du vælge placering til afløbet under hensyntagen til den primære vindretning for at fremme strømningen hen mod
afløbet.
Placer starten af vægplade CH1 40 cm fra en af enderne af væggen (M), så afløbsåbningen er midt på en af de buede dele, og perforeringsmærket
for lamperne og poolens rengøringsventil er tilgængelig og ikke dækket af væggene. Monter alle sektionsstykkerne i de nederste sporguides, og skub
vægpladen ind i rillen.
FOTO 6-1:
Fastgørelse af vægpladen (CH) i væggen (2 stk.) PEOV9159 - PEOV8059 - PEOV9127 - PEOV8027
Poolomkredsen består af to vægplader af samme længde for at lette håndteringen, eftersom det vil være for tungt i ét stykke.
Start med at montere vægpladen med perforation til afløbet (etiket med teksten SKIMMER).
En af vægpladerne har et perforeringsmærke for afløbsåbningen (CH1), og den anden del (CH2) har et perforeringsmærke for retur- eller udløbsventilerne
(VR). Når vægpladen monteres, skal du vælge placering til afløbet under hensyntagen til den primære vindretning for at fremme strømningen hen
mod afløbet.
Monter alle sektionsstykkerne i de nederste sporguides, og skub vægpladen ind i rillen.
VIGTIGT: Hvis de nederste sektionsstykker skal tilskæres, skal halvdelen af det stykke, der skal fjernes, skæres af hver halvcirkel. FØR TILSKÆRING
SKAL DU KONTROLLERE, AT VÆGPLADEN ER FØRT IND I RILLERNE I SEKTIONSSTYKKERNE I DEN BUEDE DEL HELE VEJEN RUNDT OM
POOLEN OG KORREKT MONTERET I METALBESLAGENE I DEN LIGE DEL.
Placer starten af vægpladen CH1 40 cm fra en af enderne af væggen (M), så perforeringsmærket for lamperne og poolens rengøringsventil er
tilgængelige og ikke dækket af væggene.
BEMÆRK: Den anden ende af vægpladen CH1 skal også være 40 cm fra væggen på den anden side.
MEGET VIGTIGT: Før montering af vægpladen på væggen skal de nævnte mål (40 cm) KONTROLLERES i begge ender. Sørg for at gøre det samme
før montering af den anden vægplade, CH2. Hvis disse mål ikke overholdes, vil de to halvcirkler ikke være lige store, og du vil ikke kunne fortsætte
installationen.