GRAUPNER SEA FURY 9354 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 21

GRAUPNER SEA FURY 9354 Скачать руководство пользователя страница 5

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

We reserve the right to introduce modifications. Not liable for printing errors!

01/2012

Made in

Vietnam

5

The wing halves

The servo lever, Order No. 3544, as shown in the photo, needs to be shortened on
one side and, with the servo in the centre position, mounted on the drive shaft of the
servo, or 7907.1 can be used.

Place the servos in the centre position using the receiver system. Fasten the servo to

the attachment block using the screws

included with the servos. To do so, insert the rubber grommets with the brass hollow
rivets, collar downward, into the servo flange. For drilling Ø 1.5 mm holes for the
screws, the hollow rivets can be used as a drilling template. To make it easier to push
them in, the hollow rivets can be placed onto a screwdriver of the proper size.

Now the servo cables are pulled into the wing halves and tailplane halves using a
thin string. Just behind the connector, tie the string to the cable and pull it in so that it
comes out the wing root.

«
...
3
4
5
6
7
...
»

Содержание SEA FURY 9354






















Отзывы:

Нет отзывов