GRAUPNER FOCKE WULF 190 D Скачать руководство пользователя страница 4

GRAUPNER GmbH & Co. KG      D-73230 KIRCHHEIM/TECK      GERMANY

    

No liability for printing errors. We reserve the right to introduce modifications. 

                                                         02/2007 

4

especially when carrying out adjustments - wear protective gloves. Hot 
engines can even start a fire under certain circumstances. 

• 

When the motor is running it expels hot toxic gases from the exhaust together 
with very hot fluid combustion residues which can burn you if you are not 
careful. 

• 

Remove all unused fuel from the fueltank and motor after every session. 

• 

Every time you intend to operate your model check carefully that it and 
everything attached to it (e.g. propeller, linkages, control surfaces etc.) is in 
good condition and undamaged. If you find a fault, do not fly the model until 
you have corrected it. 

• 

Model motors are usually started with the help of an electric starter which 
should be fitted with the appropriate adaptor where necessary. With fixed-
wing models an alternative is to use a “chicken stick” - a length of thick 
wooden dowel with a piece of water hose pushed over it. 

• 

Many model motors are very noisy, producing a sound level much higher than 
85 dB (A), which implies that you should wear ear defenders. Never run a 
motor without the silencer fitted. Even with a silencer, model engines can 
easily disturb your neighbours. Don’t run motors when other people expect 
peace and quiet. 

• 

If you start your motor when the model is standing on loose or sandy ground, 
the propeller will suck up sand and dust and hurl it around, and it could easily 
get in your eyes and do damage. Wear protective goggles at such times. 

• 

Take care that the glowplug clip and the glow lead cannot get tangled in the 
propeller or other rotating parts. Check the throttle linkage too. 

• 

Take particular care when carrying the model with the motor running. Hold the 
rotating parts well away from you! 

• 

Be sure to keep an adequate supply of fuel in the tank. Don’t continue to fly 
the model until the tank is drained dry. 

• 

Never fly directly over people. 

• 

Never fly directly towards people. 

 

 

• 

Keep a safe distance from residential areas: at least 1.5 km “as the crow flies”. 
The best solution is to join a model flying club and use the approved flying 
site. Always keep well clear of high-tension overhead cables. 

• 

Whenever you are working on the motor, make sure that you are on a safe 
surface and cannot slip. Get used to holding the model really securely. 

• 

Take-off and landing strips should be kept free of unauthorised people and 
movable obstacles, particularly when a model is using the strip. 

• 

Watch the aeroplane constantly while it is in the air. Models must always give 
way to full-size aircraft. 

• 

Don’t operate your aircraft from public roads, squares, school playgrounds, 
public parks or sports grounds etc., and ensure that you are always in full 
control of the model. 

• 

It is important that you can stop your motor at any time. This is achieved by 
adjusting the throttle so that the barrel closes completely when you move the 
throttle stick and trim to their end-points. If this does not work, pinch the fuel 
feed line between your fingers or pull it off the carburettor. Never try to stop 
the motor by grasping the flywheel, propeller or spinner! 

Содержание FOCKE WULF 190 D















Отзывы: