7-010 Setting the Back Wall Thickness
Illustration 7-010-01
The Zargen press ZPM is normally set at 16 mm for the drawer back walls.
Necessary tool:
Open end fork wrench 17 mm
- Slide the unit carriers to the front of the respective drawer width.
- Open both toggle levers „1“.
- Place a drawer front „2“ on both front supports „3“.
- Place a drawer bottom „4“ ( with the bottom groove toward the machine operator).
- Place a drawer back wall „5“ on the back wall support „6“.
- Press the drawer back wall down. „5“ the remaining gap „A“ between the drawer front „2“ and the
pressure disk „7“ should be about 0.5 mm. This is necessary so that the drawer can be easily removed from
the Zarge press after the compression.
Caution:
The set dimension „B“ from the lower edge of the pressure disk „7“ to the upper edge of the back
wall support „6“ is extremely important. A wrong setting may result in many possible defects.
„B“ is the bottom length minus the set gap „A“
Bottom length = total length - back wall thickness (see also the section and chart 7-001).
7-011 Setting the Bottom Thickness
Illustration 7-011-01
The Zargen press ZPM is normally set for a 16 mm thick drawer bottom.
Necessary tool:
17 mm open-end fork wrench
- Disconnect the Zargen press from the pneumatic compressed air supply.
- Close both toggle levers „1“.
- Pull both compression slides „9“ to the lowest position.
- Measure the distance „A“ between the pressure fence „10“ and the change-over insert „13“. When there
are no drawer components placed in the Zarge press:
A1 = bottom thi 1.5 mm
A2 = bottom thi 1.2 mm
- Adjust the distances, if necessary.
Loosen both clamp screws „11“ with the 17 mm open-end fork wrench (@ 1/4 turn).
Turn both adjusting screws „12“ clockwise to reduce distance „A“.
Turn both adjusting screws counterclockwise to increase distance „A“.
(1 turn equals 1.5 mm). Tighten the clamp screws.
- Reconnect the machine to the pneumatic compressed air supply.
Caution: The compression slides then move upward.
7. OPERATING THE ZPM
The star in your cabinet
31
Содержание ZPM
