manualshive.com logo in svg

GRASS VALLEY HCO-3931, Руководство пользователя

Поделиться
Скачать
GRASS VALLEY HCO-3931 Скачать руководство пользователя страница 11

USER MANUAL 

HCO-3931  |  

11

  

2 

Installation 

 

  Installing the Rear Connector Panel 

Each Grass Valley Densité-series card is associated with a rear connector panel, which must be installed in the 
Densité frame before the card can be inserted. 
 
The HCO-3931 and its associated rear connector rear panel must be mounted in a Densité-3 or Densité-3+ series 
frame. The following rear connector panels are available: 
 

 

HCO-3931-3DRP-H: Double-width Densité-3 rear HD-BNC connectors. This active rear features electronic 
latching bypass relays.  

 

HCO-3931-3TRP-HR: Triple-width Densité-3 rear HD-BNC connectors. This passive rear features hardware-
based latching bypass relays. 

 
See 2.3 - Rear Connector Panels on page 12 for for details about the signal connections available on this panel. 
 
All cards and rear connector panels can be installed with the frame powered on. The card has connectors that plug 
into a mid-frame motherboard to distribute power and connect to the controller card, as well as a second connector 
that plugs directly into the rear connector panel for input and output.  
 

To install the connector panel: 

 

The rear connector panel must be installed with the card out of the frame. 

 

1.  If a card is installed in the slot for which the rear connector panel is being changed, it must be removed. Tilting 

the swivel handle on the front of the card to lever the connectors apart, and then use the handle to pull the card 
straight out of the slot. 
 

2.  Remove the existing rear connector panel (either blank or belonging to an existing card that is being changed) 

by releasing the captive screw(s) at the bottom (Densité3+ or Densité-3+FR4) or on the side (Densité-3+FR1) of 
the panel. 

 

3.  Position the new rear connector panel and secure it in place with the captive screw(s) at the bottom or on the 

side. 

 

  Installing the HCO-3931 Card 

Once a matching rear connector panel is in place, install the HCO-3931 card as follows: 
 

1.  Open the front panel of the frame. 

 

2.  Slide the HCO-3931card into the slot and push gently on the handle to seat the connectors.  

 

When using a double-slot-width rear panel in a Densité-3+FR1 frame, the card should be inserted into the 
lower of the two slots. 

 

When using a double-slot-width rear panel in a Densité-3+FR4 frame, the card should be inserted into the 
right-most of the two slots. 

 
Inserting the card into the wrong slot will not damage the card, but the status LED on the card will flash red to 
indicate that there is no connection to the rear panel. 

 

3.  Close the front panel of the frame. 

 

Содержание HCO-3931


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды