12
Drill chuck + key
- 1 pce
5.
Chuck adapter
- 1 pce
6.
PREPARATION FOR OPERATION
INSTALLATION OF ADDITIONAL HANDLE
Due to safety issues, always use additional handle (6) when operating the rotary hammer drill. It can
be fixed in any position.
●
Turn left the wheel lock that locks handle collar (
6
) to loosen it.
Slide the handle collar over cylindrical part of the rotary hammer drill body.
●
Turn for the most comfortable position.
●
Turn the wheel lock tight to the right to clamp the handle.
●
INSTALLATION OF DEPTH GAUGE ROD
Depth gauge rod (
7
) serves to limit the depth of drill penetration of material.
Loosen the wheel lock, which blocks collar of the additional handle (
●
6
).
Slide depth gauge rod (
●
7
) into the hole in the additional handle collar.
Set desired drilling depth.
●
Fix by tightening the wheel lock.
●
INSTALLATION AND REPLACEMENT OF WORKING TOOLS
Rotary hammer drill is designed to operate with working tools with SDS-PLUS shanks. Prior to operation
clean the rotary hammer drill and working tools. Use lubricant and apply thin layer onto shank of the work-
ing tool.
Disconnect the power tool from power supply.
Rotary hammer drill features clic-clic system (which does not require to pull off the fixing sleeve (
2
) when
installing a working tool).
Put the rotary hammer against stable surface.
●
Insert working tool shank into chuck (
●
1
) and slide it to mechanical stop (it may be necessary to turn the
working tool so it can reach appropriate position) (
fig. A
).
Working tool is properly seated if it cannot be removed without pulling off the fixing sleeve.
●
If the sleeve (
●
2
) does not return to its default position, remove the working tool and repeat the whole
operation.
High efficiency of the rotary hammer drill operation can be achieved by using sharp and undamaged
working tools.
DEINSTALLATION OF WORKING TOOL
Just after the operation is finished, the working tool may be hot. Avoid direct contact and use ap-
propriate protective gloves. Clean the working tool after removal.
Disconnect the power tool from power supply.
Pull the fixing sleeve (
●
2
) to the back and hold.
Remove the working tool with your second hand by pulling it to the front.
●
OVERLOAD CLUTCH
Rotary hammer drill features overload clutch with factory setting. Spindle of the rotary hammer stops im-
mediately after working tool jams, what might overload the power tool.
Always use glasses or anti-splinter goggles, especially when drilling a hole above your head.
Содержание 58G509
