background image

Terms of manufacturer’s guarantee:

• 

The Company shall mean Grant Engineering (UK) Limited.

• 

The cylinder/thermal store must be installed by a competent 

installer and in full accordance with the relevant Codes of 

Practice, Regulations and Legislation in force at the time of 

installation.

• 

The cylinder/thermal store is guaranteed for 

two years

 from 

the date of installation

4

, providing that after twelve months 

the annual service

3

 has been completed and the cylinder/

thermal store registered with the Company within thirty days 

of the installation

4

. Any work undertaken must be authorised 

by the Company and carried out by a competent service 

engineer.

• 

The stainless steel (shell) used in the manufacture of the 

cylinder/thermal store is guaranteed for a period of 

twenty 

five years

 (parts only) from the date of installation

4

. This is 

subject to the following:
• 

The cylinder/thermal store is operated correctly, 

in accordance with the installation and servicing 

instructions.

• 

Proof is provided that the connecting system/s has been 

flushed or chemically cleaned where appropriate (refer 

to BS 7593) and that the required quantity of a suitable 

corrosion inhibitor added.

• 

Proof of annual servicing (including the checking of any 

expansion vessels and pressure relief valves) must be 

provided if and when requested by the Company.

• 

This guarantee does not cover breakdowns caused by 

incorrect installation, neglect, misuse, accident or failure to 

operate the cylinder/thermal store in accordance with the 

manufacturer’s instructions.

• 

The cylinder/thermal store is registered with the Company 

within thirty days of installation

4

. Failure to do so does not 

affect your statutory rights

1

.

• 

The balance of the guarantee is transferable providing the 

installation is serviced prior to the dwelling’s new owners 

taking up residence. Grant Engineering (UK) Limited must be 

informed of the new owner’s details.

• 

The Company will endeavour to provide prompt service in the 

unlikely event of a problem occurring, but it cannot be held 

responsible for any consequences of delay however caused.

• 

This guarantee applies to Grant Engineering (UK) Limited 

cylinders/thermal stores purchased and installed on the 

UK mainland, Isle of Wight, Channel Islands, Isle of Man 

and Scottish Isles only

2

. Provision of in-guarantee cover 

elsewhere in the UK is subject to agreement with the 

Company.

• 

All claims under this guarantee must be made to the 

Company prior to any work being undertaken. Invoices for 

call out/repair work by any third party will not be accepted 

unless previously authorised by the Company.

• 

Proof of purchase and date of installation, commissioning 

and service documents must be provided on request.

• 

If a replacement cylinder/thermal store is supplied under 

the guarantee (due to a manufacturing fault) the product 

guarantee continues from the installation date of the original 

cylinder/thermal store, and 

not

 from the installation date of 

the replacement

4

.

• 

The replacement of a cylinder/thermal store under this 

guarantee does include any consequential costs.

• 

The cylinder/thermal store must be connected to a mains 

water supply (installations utilising a private water supply are 

not covered by this guarantee).

• 

Breakdown/failure due to lime scale will not be covered by 

this guarantee.

• 

The cylinder/thermal store must not be sited in a location 

where it may be subjected to frost.

Hard water advice

If you live in a hard water area, protection against scaling in your 

cylinder/thermal store must be provided.
You should fit an appropriate scale inhibitor or water softener as 

any breakdown caused by water scaling is not covered by either 

the manufacturer’s guarantee. Ask your installer for advice. 

Foot notes:

1. 

Your statutory rights entitle you to a one year guarantee 

period only.

2.  The UK mainland consists of England, Scotland and Wales 

only. Please note that for the purposes of this definition, 

Northern Ireland and Scilly Isles are not considered part of 

the UK mainland.

3. 

We recommend that your cylinder/thermal store is serviced 

every twelve months (even when the guarantee has expired) 

to prolong the lifespan and ensure it is operating safely and 

efficiently.

4.  The guarantee period will commence from the date of 

installation, unless the installation date is more than six 

months from the date of purchase, in which case the 

guarantee period will commence six months from the date of 

purchase.

Page 37

Section 13: Guarantee

Содержание HPMONO/IND125









































Отзывы: