Grant HPMONO/IND125 Скачать руководство пользователя страница 35

Страница: 35 / 40

Section 12: User Instructions

12.1 USER INSTRUCTIONS

Your Grant MonoWave indirect HP cylinder has been designed to

give many years of trouble-free service and is made from hygienic

high grade stainless steel.

IMMERSION HEATERS

Your Grant MonoWave indirect HP cylinder is fitted with one 3kW

immersion heater (two 3kW immersion heaters are fitted to the

300 & 400 models). Refer to Section 5.1 for further details.

The immersion heater/s in the cylinder can be used to heat your

hot water when your heat pump (or boiler) is switched off, e.g.

during the summer months.
In the case of a Grant Aerona³ heat pump, this immersion heater

may also be used to assist in the heating of your hot water if you

have a Grant Boost Kit fitted. Check with your installer.
The cylinder immersion heater/s has been factory-set to position

4 (refer to Figure 5-1) to give a hot water temperature of around

60°C.
The immersion heater/s incorporates an in independent non self-

resetting over temperature cut-out device to prevent excessive

water temperatures. If this safety cut-out operates it can be re-set.

Refer to Section 6.3.
If the problem persists, please contact your installer.

DUAL THERMOSTAT

Your Grant MonoWave indirect HP cylinder is also fitted with a

Dual Thermostat (mounted on the cylinder). Refer to Section 5.4

for further details.
The cylinder control thermostat has an adjustment range between

25°C and 65°C. It is recommended that it is set to 60°C.

The high limit (overheat) thermostat will automatically operate if

the water temperature reaches 90°C. If this operates it can be

re-set. To do this, first wait for the cylinder to cool down. Then

unscrew the plastic cap and press in the small re-set pin.
If the problem persists, please contact your installer.

TEMPERATURE SETTINGS

The hot water temperatures on the cylinder immersion heater and

dual thermostat should not be set any higher than 60°C otherwise

nuisance tripping of either the immersion heater safety cut-out, or

the high limit thermostat (in the dual thermostat) will occur.
If you are in any doubt, these temperature adjustments should be

best left to your installer.

HOT WATER

When a hot tap is turned on there may be a short surge of water,

this is quite normal with unvented systems and does not mean

there is a fault.

When you first fill a basin the water may sometimes appear milky.

This is due to very tiny air bubbles in the water, which will clear

very quickly.

! WARNING !

If water is seen to flow from either the Temperature &

Pressure Relief (T&P Valve) valve or the Expansion Relief
Valve (EV) on the cylinder seek expert advice immediately.

If the water is flowing from the T&P Valve, immediately:

Shut off the electrical supply to the immersion

heater(s).

2. Shut down the boiler or other heat sources to the

cylinder e.g. solar, heat pump, etc.

3. DO NOT SHUT OFF THE WATER SUPPLY TO THE

CYLINDER.

4. Contact your installer to check the system.
IMPORTANT

Do NOT tamper with any of the Safety controls fitted to the

cylinder. If you suspect a fault always contact a competent

installer who is qualified to work on unvented water

cylinders.

12 USER INSTRUCTIONS

Page 35

Содержание HPMONO/IND125









































Результаты поиска

Содержание HPMONO/IND125

Отзывы:

Похожие инструкции для HPMONO/IND125

Бренды по названию

Популярные бренды

Grant HPMONO/IND125, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание HPMONO/IND125

Отзывы:

Похожие инструкции для HPMONO/IND125

Бренды по названию

Популярные бренды