Graco XP70 Скачать руководство пользователя страница 8

Страница: 8 / 56

Important Two-Component Material Information

3A0420H

Changing Materials

•

Changing material types used in your sprayer
requires special attention to avoid equipment dam-
age and downtime.

•

Always clean the fluid inlet strainers after flushing.

•

When changing between epoxies and urethanes or
polyureas, disassemble and clean all fluid compo-
nents and changes hose sets.

•

Check with your material manufacturer for chemical
compatibility.

•

Most materials use ISO on the A side, but some use
ISO on the B side.

•

Epoxies often have amines on the B (hardener)
side. Polyureas often have amines on the B (resin)
side.

A and B Component Designations

Material suppliers and markets refer to plural component materials differently. The table below summarizes the differ-
ent designations for the components used in various machines.

Market

Equipment

Designations

Machine Left

Side

Machine Right

Side

Foam and Polyurea, and

Urethane Pour

All Reactors, HFR

™

and VRM

™

Letter

Color

Red

Blue

Component Names

ISO, Hardener,

Catalyst

Polyol, Resin,

Base

Major or Minor Component
(when not 1:1 mix)

Low Volume

Side

High Volume

Side

Epoxy and Urethane

Protective Coatings

Hydra-Cat

, Xtreme-

Mix

™

, XM

™

, and

XP70

Letter

Color

Blue

Green

Component Names

Resin, Base

Hardener, Cata-

lyst

Major or Minor Component
(when not 1:1 mix)

High Volume

Side

Low Volume

Side

Epoxy, Silicone, Ure-

thanes, and other mate-

rials

PR70

™

and PR

Letter

Color

Red

Blue

Component Names

Polyol, Resin,

Base

ISO, Hardener,

Catalyst

Major or Minor Component
(when not 1:1 mix)

High Volume

Side

Low Volume

Side

Содержание XP70

























































Результаты поиска

Содержание XP70

Отзывы:

Graco XP70, Инструкция и каталог запасных частей, Страница: 8 / 56

Результаты поиска

Содержание XP70

Отзывы: