Graco XP70 Скачать руководство пользователя страница 53

Страница: 53 / 56

Technical Data

3A0420H

Technical Data

Volume

Mix Ratio

Pressure

Ratio

“A” Side

Pump

“B” Side

Pump

Combined

Fluid Output

cc/cycle

Maximum Air

Working Pressure

psi (MPa, bar)

Maximum Fluid

Working Pressure

psi (MPa, psi)

Flow Rate at

40 cycles/min

gpm (ltr/min)

1:1

76:1

Xtreme 85

173

95 (0.6, 6.5)

7250 (50, 500)

1.8 (6.9)

1.5:1

91:1

Xtreme 85

Xtreme 58

144

80 (0.5, 5.5)

7250 (50, 500)

1.5 (5.7)

2:1

76:1

Xtreme 115

Xtreme 58

174

95 (0.6, 6.5)

7250 (50, 500)

1.8 (6.9)

2.5:1

65:1

Xtreme 145

Xtreme 58

203

100 (0.7, 7)

6500, 45, 448)

2.1 (8.1)

3:1

68:1

Xtreme 145

Xtreme 48

193

100 (0.7, 7)

6800, 47, 469)

2.0 (7.7)

4:1

73:1

Xtreme 145

Xtreme 36

181

100 (0.7, 7)

7250 (50, 500)

1.9 (7.2)

Air inlet size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3/4 npsm(f)

Air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

75 cfm at 100 psi inlet/gpm
0.56 cu meter/min at 7 bar/liter/min

Maximum air pressure supply to the sprayer . . . . . . . . . . . . .

175 psi (1 MPa, 12 bar)

Filtration:

Air inlet filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40-micron filter/separator included

XP70 pump outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 mesh

XTR7 Spray Gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

60 mesh

Fluid pump inlets without hoppers. . . . . . . . . . . . . . . . . . . . . .

1-1/4 in. npsm(m)

Fluid gauge manifold outlets . . . . . . . . . . . . . . . . . . . . . . . . . .

1/2 in. npt(f)

Fluid mix manifold inlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3/8 in. npt(m) ball valves

Mix manifold material outlet . . . . . . . . . . . . . . . . . . . . . . . . . .

1/2 in. npt(f)

Maximum feed pressure from remote source . . . . . . . . . . . . .

250 psi (1.7 MPa, 17 bar)

Fluid Viscosity Range:

Gravity feed with 7 gallon (26 liter) hoppers . . . . . . . . . . . .

200 to 20,000 cps (pourable)

Pressure feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Any viscosity that will not require feed pressure more than 15%
of outlet pressure

Environmental Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Indoor/outdoor

Hazardous Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

EX II 2 G c IIA T2

Ambient Temperature Range:

Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40-130°F (4-54°C)

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30-160°F (-1-71°C)

Maximum Fluid Temperature . . . . . . . . . . . . . . . . . . . . . . .

160°F (71°C)

Sound pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86 dBA at 100 psi (0.7 MPa, 7 bar)

Sound power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

98 dBA at 100 psi (0.7 MPa, 7 bar)

Wetted materials:

Housings and manifolds . . . . . . . . . . . . . . . . . . . . . . . . . . .

Carbon steel with electroless nickel plating

Miscellaneous parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Plated carbon steel, stainless steels, carbide, acetal, UHM-
WPE, nylon, PTFE solvent resistant plastics

Pump packings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Carbon filled PTFE

Flush pump suction tube. . . . . . . . . . . . . . . . . . . . . . . . . . .

Aluminum

Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Nylon core

Weight:

Full System with heaters, solvent flush pump, and hoppers

575 lbs (260 kg)

Bare system with no heaters, solvent flush pump, or hoppers 425 lbs (192 kg)

Maximum Storage Time:

5 years (To maintain original performance, replace soft seals
after 5 years of inactivity.)

Maximum Lifetime:

Indefinite with recommended maintenance and periodic
rebuilds for critical parts.

Power Efficiency Factor:

75 cu. ft compressed air/1 gallon sprayed material at 100 psi

0.56 m

compressed air /1 liter sprayed material at 0.7 MPa

(7 bar)

Содержание XP70

























































Результаты поиска

Содержание XP70

Отзывы:

Graco XP70, Инструкция и каталог запасных частей, Страница: 53 / 56

Результаты поиска

Содержание XP70

Отзывы: