Graco XP70 страница 52 Скачать руководство пользователя | Manualshive

Страница: 52 / 56

background image

Accessories and Kits

52

3A0420H

Accessories and Kits

Acceptable For Use in Explosive
Atmospheres

Blue 7 Gallon Hopper Kit, 24F376
Green 7 Gallon Hopper Kit, 24F377

Mount to the sides of an XP70 sprayer. See manual
406860 for more information.

Solvent Pump Kit, 262393

For supplying solvent to the mix manifold. See manual
310863 for more information.

Desiccant Dryer Kit, 262454

For use with polyurethane isocyanates in 7-gallon hop-
pers. See manual 406739 for more information.

Desiccant Dryer Filter 2 Pack, 119974

Heater Adapter Kit, 262450

Hose and fittings for connecting Viscon HP heaters to
XP70 sprayer.

See manual 406861 for parts. Purchase

heaters separately, see heater manual for part numbers.

Twistork Agitator Kit, 256274

For mixing viscous materials held within a 55-gallon
drum. See manual 312769 for more information.

5:1 Feed Pump Kit, 256276

For supplying viscous materials from a drum to a XP70
sprayer. See manual 312769 for more information.

5:1 Drum Feed Kit, 256255

One 5:1 pump feed kit and one Twistork agitator kit for
mixing and supplying viscous materials from a 55-gallon
drum to a XP70 sprayer. See manual 312769 for more
information.

10:1 Drum Feed Kit, 256433

For supplying highly viscous material from a 55-gallon
drum to a XP70 sprayer. See manual 312769 for more
information.

Remote Mix Manifold Carriage, 262522

A protective guard to mount mix manifold remote. See
mix manifold manual for more information.

Gun Splitter, 234026

One splitter valve to use two spray guns with a propor-
tioner. It can be used with one gun or two and provides
for independent flushing of each gun while the other gun
remains in use. See manual 309964 for more informa-
tion.

DataTrak

™

Conversion Kit, NXT606

Intrinsically safe battery operated NXT air motor acces-
sory for material tracking system diagnostics and run-
away control. See manual 311486 for more information.

Not Approved For Explosive
Atmospheres

These kits do not carry the EX mark.

2:1 Feed Pump Kit, 256275

For supplying viscous materials from a drum to a XP70
sprayer. See manual 312769 for more information.

2:1 Drum Feed Kit, 256232

One T2 pump feed kit and one Twistork agitator kit for
mixing and supplying viscous materials from a 55-gallon
drum to a XP70 sprayer. See manual 312769 for more
information.

«
...
50
51
52
53
54
...
»

Содержание XP70

























































Отзывы:

Нет отзывов

Похожие инструкции для XP70

Бренд: Parkside Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды