manualshive.com logo in svg

Graco XP70, Инструкция и каталог запасных частей

Graco XP70 - инструкция и запчасти в руководстве. Скачайте бесплатно руководство по эксплуатации для удобного использования вашей техники. Посетите manualshive.com для загрузки.

Поделиться
Скачать
background image

Repair 

34

3A0420H

Remove Air Motor

1.

Cycle the yoke and pump rods near the bottom of 
their stroke. Follow 

Shutdown

, page 28.

2.

Disconnect the air line from the air motor (103).

3.

Remove the air motor rod cover (121) and pump 
guards (122).

4.

Use a wrench to hold the tie rod (102) flats to keep 
the rods from turning. Unscrew the nuts (108) and 
washers (107) from the tie rods.

5.

Place a wrench on adapter rod (104). Use tool (70) 
to loosen the serrated yoke nut (109) that holds the 
air motor (103) above the yoke (111).

6.

Face the front of the machine and slide the air motor 
(103) to the opening in the yoke (111).

7.

Use a hoist to remove the air motor by the lift ring.

8.

Refer to the air motor manual to service or repair the 
air motor.

9.

Follow the steps in reverse order to reinstall the air 
motor.

NOTE: Position air motor for correct mix ratio. See 
Air Motor Position on page 18 for instructions. 
Torque nuts (108) to 50-60ft-lb (68-81 N•m).

Air Controls

See F

IG

. 8 on page 35.

Replace Air Control Assembly

1.

Close the main air shutoff valve on the air supply 
line and on the system. Depressurize the air line.

2.

Disconnect the air motor air lines and system air 
line.

3.

Remove the nut (8) and washer (5). Remove the 
bottom air control manifold assembly from the cart.

4.

Loosen the upper air control assembly from the air 
motor.

5.

Follow the steps in reverse order to reinstall the new 
air control assembly.

Replace Air Filter Element

1.

Close the main air shutoff valve on the air supply 
line and on the system. Depressurize the air line.

2.

Unscrew the serrated ring on filter bowl (210).

3.

Remove and replace the filter element (210a). See 

Air Controls, 258983

, page 46.

Replace System Air Regulator

1.

Close the main air shutoff valve on the air supply 
line and on the system.

2.

Disconnect air motor air lines and system air line.

3.

Remove the regulator assembly (201) and replace 
with new regulator. See 

Air Controls, 258983

, page 

46.

4.

Follow the steps in reverse order to reassemble.

103

121

122

r_258914_3a0420a_7a

lift ring

102

108

107

109

111

r_2

5891

4_3a

0420

a_8a

104

Содержание XP70

























































Отзывы:

Нет отзывов

Похожие инструкции для XP70

Cocraft 40-9513 Original Instructions Manual preview
40-9513
Бренд: Cocraft Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды