background image

Warnings 

6

3A0142A

3.

Install ratchet (59) to side of spool using screws (48) 
(F

IG

. 12)

4.

Position guide arm and pedestal base (24 / 30) 
assembly over spool. Adjust as needed to correctly 
align parts (F

IG

. 11).

5.

Replace snap ring (25) (F

IG

. 11, page 5).

Unless otherwise noted, steps 6 - 13 refer to F

IG

. 7, 

page 4.

6.

Install washers (15 / 16) over end of bolt (18) and 
slide them over the threads to the bolt head. 

7.

Slide bolt (18) through hole in center of spool. Do 
NOT tighten bolt.

8.

Stand hose reel assembly upright on the base (24).

9.

Install swivel assembly (3 / 22 / 23) and (if removed) 
washer (7) in spool. Align fitting (23) with opening 
(A) in side of spool. For hose reel to operate cor-
rectly, these parts must be aligned correctly (F

IG

13).

10. Tighten bolt (18).

11. Align pedestal assembly (26) to base (24). Install 2 

screws (27). Tighten and torque screws to 20-30 ft. 
lbs (89 - 133 N.m).

12. Align guide arm (30) and hose guide (31). Install 

and tighten screws (52) and nuts (53).

13. Install large nut (32). Tighten and torque nut to 

85-105 ft. lbs (378 - 467 N.m).

14. Insert the hose fitting end (B) of hose through the 

hose guide (31) and connect hose end to the hose 
reel swivel fitting (23) (F

IG

. 14). Tighten securely.

15. Reinstall hose reel to wall, ceiling or truck bed.

16. Insert end of hose through hose guide. Install stop 

to end of hose. 

17. Set spring tension following Adjusting Spring Ten-

sion instructions on page 6. 

F

IG

. 12

59

48

9

F

IG

. 13

F

IG

. 14

23

A

7

22

3

B

23

Содержание XD30 Series











Отзывы: