Graco XD30 Series Скачать руководство пользователя

Страница: 6 / 10

Warnings

3A0142A

Install ratchet (59) to side of spool using screws (48)
(F

. 12).

Position guide arm and pedestal base (24 / 30)
assembly over spool. Adjust as needed to correctly
align parts (F

. 11).

Replace snap ring (25) (F

. 11, page 5).

Unless otherwise noted, steps 6 - 13 refer to F

. 7,

page 4.

Install washers (15 / 16) over end of bolt (18) and
slide them over the threads to the bolt head.

Slide bolt (18) through hole in center of spool. Do
NOT tighten bolt.

Stand hose reel assembly upright on the base (24).

Install swivel assembly (3 / 22 / 23) and (if removed)
washer (7) in spool. Align fitting (23) with opening
(A) in side of spool. For hose reel to operate cor-
rectly, these parts must be aligned correctly (F

13).

10. Tighten bolt (18).

11. Align pedestal assembly (26) to base (24). Install 2

screws (27). Tighten and torque screws to 20-30 ft.
lbs (89 - 133 N.m).

12. Align guide arm (30) and hose guide (31). Install

and tighten screws (52) and nuts (53).

13. Install large nut (32). Tighten and torque nut to

85-105 ft. lbs (378 - 467 N.m).

14. Insert the hose fitting end (B) of hose through the

hose guide (31) and connect hose end to the hose
reel swivel fitting (23) (F

. 14). Tighten securely.

15. Reinstall hose reel to wall, ceiling or truck bed.

16. Insert end of hose through hose guide. Install stop

to end of hose.

17. Set spring tension following Adjusting Spring Ten-

sion instructions on page 6.

. 12

. 13

. 14

Содержание XD30 Series











Результаты поиска

Содержание XD30 Series

Отзывы:

Похожие инструкции для XD30 Series

Бренды по названию

Популярные бренды

Graco XD30 Series, Инструкция по эксплуатации

Результаты поиска

Содержание XD30 Series

Отзывы:

Похожие инструкции для XD30 Series

Бренды по названию

Популярные бренды