Graco WB3000 Скачать руководство пользователя страница 49

Страница: 49 / 78

Repair

NOTICE

Do not overtighten the ﬂuid seat housing (24).

Overtightening may damage the housing and

the gun barrel, resulting in improper ﬂuid

shutoff.

6. Trigger the gun and install the ﬂuid seat housing

(24). Tighten until snug, then 1/4 turn more.

7. Check that the spray tip gasket (27a) is in place.

Align the spray tip tab with the groove in the air

cap (25). Install the spray tip (27) in the air cap.

8. Make sure that the electrode (25a) is installed

correctly in the air cap.

9. Check that the air cap o-ring (25b) is in place.
10. Check that the u-cup (22a) is in place on the

retaining ring (22). The lips of the u-cup must

face forward.

NOTICE

To avoid damaging the tip guard, orient the

air cap assembly (25) before tightening the

retaining ring (22). Do not turn the air cap

when the retaining ring is tight.

11. Orientate the air cap and tighten the retaining

ring securely.

12. See

Test Gun Resistance, page 36

Electrode Replacement

NOTICE

For best performance and to avoid potential

damage to the spray gun, do not operate the spray

gun without the electrode installed in the air cap.

1. See

Prepare the Gun for Service, page 47

2. Remove the air cap assembly (25). See

Air Cap, Spray Tip, and Fluid Seat Housing

Replacement, page 48

3. Pull the electrode (25a) out of the back of the air

cap, using a needle-nose pliers.

4. Push the new electrode through the air cap hole.

Make sure the short end (BB) of the electrode

engages the hole (CC) in the back of the air

cap. Press the electrode in place ﬁrmly with your

ﬁngers.

5. Install the air cap assembly.
6. See

Test Gun Resistance, page 36

Figure 26 Replace Electrode

3A2497C

Содержание WB3000















































































Результаты поиска

Содержание WB3000

Отзывы:

Похожие инструкции для WB3000

Бренды по названию

Популярные бренды

Graco WB3000, Инструкция - Каталог запасных частей

Результаты поиска

Содержание WB3000

Отзывы:

Похожие инструкции для WB3000

Бренды по названию

Популярные бренды