Graco WB3000 Скачать руководство пользователя страница 11

Страница: 11 / 78

Gun Overview

Table 1 . Key for Figs. 2–9.

Item

Description

Purpose

Voltage Adjustment Switch

Two-position switch sets smart gun

voltage to low setting (LO) or high

setting (HI). This switch is functional

in Operating Mode and in Diagnostic

Mode.

Low Voltage Mode Indicator

Lights (blue) when the smart gun is

set to Low Voltage.

Voltage (kV) Display

Displays actual spraying voltage of

the gun, in kV. In Operating Mode,

display is a bar graph. In Diagnostic

Mode, voltage is displayed as a

number.

Current (uA) Display

Displays actual spraying current of

the gun, in uA. In Operating Mode,

display is a bar graph. In Diagnostic

Mode, current is displayed as a

number.

LO SET button

Press momentarily to enter the Low

Voltage Setting screen.
Press and hold for approximately 5

seconds to enter or exit Diagnostic

Mode.
While in Diagnostic Mode, press

momentarily to advance through

screens.
While on the Low Voltage Lock

Screen (in Diagnostic Mode), press

and hold to turn the lock on or off.

Low Voltage Display

Displays the low voltage setting

as a number. The setting can be

changed. See Fig. 4.

Low Voltage Locked

Appears if the low voltage setting is

locked. See Fig. 5 and Fig. 9.

Lo Display

Appears on the Low Voltage Lock

Screen. See Fig. 9.

Error Display

Appears if the Smart module loses

communication with the power

supply. See Fig. 3.

Voltage Indicator

In Diagnostic Mode, the two top right

LEDs of the screen light, indicating

that the value displayed is in kV. See

Fig. 6.

Current Indicator

In Diagnostic Mode, the two bottom

right LEDs of the screen light,

indicating that the value displayed is

in uA. See Fig. 7.

3A2497C

Содержание WB3000















































































Результаты поиска

Содержание WB3000

Отзывы:

Похожие инструкции для WB3000

Бренды по названию

Популярные бренды

Graco WB3000, Инструкция - Каталог запасных частей

Результаты поиска

Содержание WB3000

Отзывы:

Похожие инструкции для WB3000

Бренды по названию

Популярные бренды