Graco WB3000 Скачать руководство пользователя страница 16

Страница: 16 / 78

Installation

Air Supply Line

1. See Fig. 12. Install an air line ﬁlter/water

separator (M) on the main air supply line to

ensure a dry, clean air supply to the gun. Dirt and

moisture can ruin the appearance of your ﬁnished

workpiece and can cause the gun to malfunction.

2. The WB3000 system includes a bleed-type air

regulator (N) on the gun air supply line (P), to

control air pressure to the gun.

To reduce the risk of electric shock or other

serious injury, you must use the red-colored

Graco Electrically Conductive Air Hose for the

gun air supply, and you must connect the hose

ground wire to a true earth ground. Do not use

the black or gray-colored Graco air hoses.

3. Connect the red-colored Graco Electrically

Conductive Air Hose (P) between the gun air

regulator (N) and the gun’s air inlet. The gun air

inlet ﬁtting has a left-hand thread. Connect the

air supply hose ground wire (Q) to a true earth

ground.

Trapped air can cause the ﬂuid supply unit to

cycle unexpectedly, which can result in serious

injury, including splashing ﬂuid in the eyes or

on the skin. Do not operate the equipment

without the bleed-type air valve (B) installed.

4. The WB3000 system includes a bleed-type air

valve (B). The bleed-type air valve is required

to shut off all air to the system and relieve air

trapped between the valve and the ﬂuid supply

unit after the air regulator is shut off. Connect the

main air supply line (A) to the bleed valve.

5. Install an additional bleed-type air valve (CC)

upstream of the air ﬁlter (M) to isolate the ﬁlter

for servicing.

Ground the Cabinet

Connect the main ground wire (V) to a true earth

ground.

3A2497C

Содержание WB3000















































































Результаты поиска

Содержание WB3000

Отзывы:

Похожие инструкции для WB3000

Бренды по названию

Популярные бренды

Graco WB3000, Инструкция - Каталог запасных частей

Результаты поиска

Содержание WB3000

Отзывы:

Похожие инструкции для WB3000

Бренды по названию

Популярные бренды