Graco True Airless LTS15 Скачать руководство пользователя страница 14

Страница: 14 / 56

Start Up

3A3529C

If you suspect the spray tip or hose is

clogged or that pressure has not been

fully relieved:
a.

VERY SLOWLY loosen the tip

guard retaining nut or the hose end

coupling to relieve pressure

gradually.

Loosen the nut or coupling

completely.

Clear airless hose or spray tip

obstruction. See

Clear Tip Clog

page 21.

Flush Storage Fluid

This sprayer arrives from the factory with a

small amount of test material in the system.

is important that you flush this material

from the sprayer before using it for the first

time.

See

Cleaning Fluid Compatibility

and

Static Grounding Instructions (Oil-Based

materials)

, page 29 for additional information

when using oil-based materials.
1.

Perform

Pressure Relief Procedure

page 13.

Make certain ON/OFF switch is

OFF

Separate drain tube (smaller) from suc-

tion tube (larger).

Place drain tube in a waste pail.

Submerge suction tube in a pail par-

tially filled with water or flushing fluid.

If spraying oil-based materials, sub-

merge the suction tube in mineral spir-

its, or compatible cleaning solvent. If

spraying water-based materials, sub-

merge the suction tube in water.

Turn Prime/Spray valve down to

PRIME position.

Plug power supply cord into a properly

grounded electrical outlet.

Press PushPrime button twice to

loosen inlet valve ball.

Align setting indicator with Prime/Clean

setting on pressure control knob.

10. Turn ON/OFF switch to

position.

11. When sprayer starts pumping, flushing

solvent and air bubbles will be purged

from system. Allow fluid to flow out of

drain tube, into waste pail, for 30 to 60

seconds.

12. Turn ON/OFF switch to

OFF

position.

ti27467a

ti27120a

ti28235a

ti27135a

ti27134a

Содержание True Airless LTS15

























































Результаты поиска

Содержание True Airless LTS15

Отзывы:

Похожие инструкции для True Airless LTS15

Бренды по названию

Популярные бренды

Graco True Airless LTS15, Руководство пользователя

Результаты поиска

Содержание True Airless LTS15

Отзывы:

Похожие инструкции для True Airless LTS15

Бренды по названию

Популярные бренды