background image

Cleanup 

24

3A3529C

7.

Screw Power Flush attachment valve to 

garden hose. Close valve.

8.

Turn on water. Open valve. Rinse paint 

off suction tube, drain tube and inlet 

strainer. Close valve.

9.

Unscrew inlet strainer from suction 

tube. Place inlet strainer in waste pail.

10. Connect garden hose to suction tube 

with Power Flush attachment valve. 

Leave drain tube in waste pail.

11. Turn ON/OFF switch to 

ON

 position.

12. Open Power Flush attachment valve.
13. Circulate water through sprayer, into 

waste pail, for 20 seconds.

14. Turn ON/OFF switch to 

OFF

 position.

NOTE: 

Step 15 is for returning paint in hose 

to paint pail. One 50 ft (15 m) hose holds 

approximately 1 quart (1 liter) of paint.

15. To recover paint in hose, point gun into 

paint pail while holding gun firmly to the 

pail.
a.

Disengage trigger lock.

b.

Pull and hold gun trigger.

c.

Turn Prime/Spray valve horizontal 

to SPRAY position.

d.

Turn ON/OFF switch to 

ON

 position.

e.

Continue to hold gun trigger until 

you see paint diluted with flushing 

fluid starting to come out of gun.

16. While continuing to trigger gun, quickly 

move gun to redirect spray into waste 

pail. Continue triggering gun into waste 

pail until flushing fluid dispensed from 

gun is relatively clear.

17. Turn pressure control knob to the low-

est setting. 

ti27135a

7155a

ti27

ti27158a

ti27159a

ti27148a

A

B

C

D

ti27151a

Содержание True Airless LTS15

























































Отзывы: