Graco True Airless LTS15 Скачать руководство пользователя

Страница: 24 / 56

Cleanup

3A3529C

Screw Power Flush attachment valve to

garden hose. Close valve.

Turn on water. Open valve. Rinse paint

off suction tube, drain tube and inlet

strainer. Close valve.

Unscrew inlet strainer from suction

tube. Place inlet strainer in waste pail.

10. Connect garden hose to suction tube

with Power Flush attachment valve.

Leave drain tube in waste pail.

11. Turn ON/OFF switch to

position.

12. Open Power Flush attachment valve.
13. Circulate water through sprayer, into

waste pail, for 20 seconds.

14. Turn ON/OFF switch to

OFF

position.

NOTE:

Step 15 is for returning paint in hose

to paint pail. One 50 ft (15 m) hose holds

approximately 1 quart (1 liter) of paint.

15. To recover paint in hose, point gun into

paint pail while holding gun firmly to the

pail.
a.

Disengage trigger lock.

Pull and hold gun trigger.

Turn Prime/Spray valve horizontal

to SPRAY position.

Turn ON/OFF switch to

position.

Continue to hold gun trigger until

you see paint diluted with flushing

fluid starting to come out of gun.

16. While continuing to trigger gun, quickly

move gun to redirect spray into waste

pail. Continue triggering gun into waste

pail until flushing fluid dispensed from

gun is relatively clear.

17. Turn pressure control knob to the low-

est setting.

ti27135a

7155a

ti27

ti27158a

ti27159a

ti27148a

ti27151a

Содержание True Airless LTS15

























































Результаты поиска

Содержание True Airless LTS15

Отзывы:

Похожие инструкции для True Airless LTS15

Бренды по названию

Популярные бренды

Graco True Airless LTS15, Руководство пользователя

Результаты поиска

Содержание True Airless LTS15

Отзывы:

Похожие инструкции для True Airless LTS15

Бренды по названию

Популярные бренды