Graco True Airless LTS15 Скачать руководство пользователя

Страница: 13 / 56

Start Up

3A3529C

Start Up

Pressure Relief Procedure

Follow the Pressure Relief

Procedure whenever you see this

symbol.

Turn ON/OFF switch to the

OFF

position.

Engage the trigger lock. Always engage

the trigger lock when sprayer is stopped

to prevent the gun from being triggered

accidentally.

Turn pressure control knob to lowest

setting.

Put drain tube into a waste pail and turn

Prime/Spray valve in PRIME position

(drain) to relieve pressure.

Hold the gun firmly to a pail. Point gun

into pail. Disengage the trigger lock and

trigger the gun to relieve pressure.

Engage the trigger lock.

This equipment stays pressurized until

pressure is manually relieved. To help

prevent serious injury from pressurized

fluid, such as skin injection or splashed

fluid, follow the

Pressure Relief

Procedure

whenever sprayer is stopped

and before sprayer is cleaned or checked,

and before equipment is serviced.

ti27118a

ti25198b

ti27493a

ti27120a

ti27466a

Содержание True Airless LTS15

























































Результаты поиска

Содержание True Airless LTS15

Отзывы:

Похожие инструкции для True Airless LTS15

Бренды по названию

Популярные бренды

Graco True Airless LTS15, Руководство пользователя

Результаты поиска

Содержание True Airless LTS15

Отзывы:

Похожие инструкции для True Airless LTS15

Бренды по названию

Популярные бренды