Graco Pro Xp L40T10 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 78

background image

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-speciﬁc

risks. When these symbols appear in the body of this manual or on warning labels, refer back to these

Warnings. Product-speciﬁc hazard symbols and warnings not covered in this section may appear throughout

the body of this manual where applicable.

WARNING

FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help

prevent ﬁre, explosion, and electric shock:
• Electrostatic equipment must be used only by trained, qualiﬁed personnel who understand

the requirements of this manual.

• Ground all equipment, personnel, object being sprayed, and conductive objects in or close to

spray area. Resistance must not exceed 1 megohm. See Grounding instructions.

• Only use grounded Graco conductive air supply hoses.
• Do not use pail liners unless they are conductive and grounded.
• Stop operation immediately if static sparking occurs or you feel a shock. Do not use

equipment until you identify and correct the problem.

• Check gun resistance, hose resistance, and electrical grounding daily.
• Use and clean equipment only in well ventilated area.
• Interlock the gun air supply to prevent operation unless ventilating fans are on.
• Use cleaning solvents with highest possible ﬂash point when ﬂushing or cleaning equipment.
• To clean the exterior of the equipment, cleaning solvents must have a ﬂash point at least

5°C above ambient temperature.

• Always turn the electrostatics off when ﬂushing, cleaning or servicing equipment.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and

plastic drop cloths (potential static arc).

• Do not plug or unplug power cords or turn lights on or off when ﬂammable fumes are present.
• Keep spray area free of debris, including solvent, rags and gasoline.
• Keep a working ﬁre extinguisher in the work area.

4

3A2494E

«
...
2
3
4
5
6
...
»

Содержание Pro Xp L40T10















































































Отзывы:

Нет отзывов

Похожие инструкции для Pro Xp L40T10

FALCON Boom Series

Бренд: Hardi Страницы: 40

Бренд: Jacto Страницы: 32

BACKPACK SPRAYER 94573

Бренд: One Stop Gardens Страницы: 11

Бренд: Dino-Power Страницы: 25

HousePainter EZ5000 Series

Бренд: Campbell Hausfeld Страницы: 36

Бренд: YATO Страницы: 76

Бренд: SAMES KREMLIN Страницы: 47

Бренд: MS Schippers Страницы: 21

Бренд: Task Force Tips Страницы: 8

Бренд: Raider Страницы: 82

Бренд: Meganex Страницы: 13

Бренд: DeVilbiss Страницы: 17

Бренд: SMK Страницы: 8

Flicker Machine

Бренд: Faithfull Страницы: 2

Platinum PZP3000

Бренд: Paint Zoom Страницы: 13

Бренд: Lafferty Страницы: 4

Бренд: WAGNER Страницы: 20

Бренд: California Air Tools Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды