Graco Pro Xp L40T10 Скачать руководство пользователя страница 35

Страница: 35 / 78

Troubleshooting

Electrical Troubleshooting

Problem

Cause

Solution

ES On/Off switch is OFF (O).

Turn ON (I).

Gun air pressure too low (ES

indicator is amber).

Check air pressure to gun;

minimum 45 psi (0.32 MPa, 3.2

bar) needed at gun for full voltage.

Atomizing air pressure too high.

Decrease.

Incorrect distance from gun to part. Should be 8-12 in. (200-300 mm).
Poorly grounded parts.

Resistance must be 1 megohm or

less. Clean workpiece hangers.

Faulty gun resistance.

See

Test Gun Resistance, page 31

Low ﬂuid resistivity.

See

Check Fluid Resistivity, page 26

Fluid leaks from the packing (2c)

and causes a short.

See

Packing Rod Repair, page 40

Poor wrap.

Faulty alternator.

See

Alternator Removal and

Replacement, page 44

ES On/Off switch is OFF (O).

Turn ON (I).

ES or Hz indicator is not lit.

No power.

Check power supply, alternator,

and alternator ribbon cable. See

Power Supply Removal and

Replacement, page 43

and

Alternator Removal and

Replacement, page 44

Operator not grounded or is near

ungrounded object.

See

Grounding, page 21

Operator gets mild shock.

Gun not grounded.

See

Check Gun Electrical

Grounding, page 25

, and

Test Gun Resistance, page 31

Operator gets shock from

workpiece.

Workpiece not grounded.

Resistance must be 1 megohm or

less. Clean workpiece hangers.

3A2494E

Содержание Pro Xp L40T10















































































Результаты поиска

Содержание Pro Xp L40T10

Отзывы:

Похожие инструкции для Pro Xp L40T10

Бренды по названию

Популярные бренды

Graco Pro Xp L40T10, Инструкция - Каталог запасных частей

Результаты поиска

Содержание Pro Xp L40T10

Отзывы:

Похожие инструкции для Pro Xp L40T10

Бренды по названию

Популярные бренды