Graco Pro Xp L40T10 Скачать руководство пользователя страница 40

Страница: 40 / 78

Repair

Fluid Packing Rod Removal

1. See

Prepare the Gun for Service, page 37

2. Remove the air cap and ﬂuid nozzle. See

Air Cap and Nozzle Replacement, page 38

3. Remove the electrode. See

Electrode Replacement, page 39

4. Loosen the trigger screws (13) and remove the

trigger (12).

5. Remove the packing rod (2), using the multi-tool

(41). Remove the spring (17).

6. Check all parts for wear or damage and replace

if necessary.

Figure 22 Fluid Packing Rod Removal

Packing Rod Repair

NOTE: You may replace the packing rod as individual

parts or as an assembly.

Adjust the Air Flow Lead and Lag

NOTE: The gun begins emitting air before the ﬂuid

is discharged and the ﬂuid stops before the air ﬂow

stops. The packing rod assembly is pre-adjusted at

the factory for proper air lead and lag. Adjust only

if necessary, as follows.
1. Remove the spring (17) from the nut (2k).
2. Use a hex wrench to hold the end of the packing

rod. Turn both adjustment nuts (2j, 2k) out to

increase the lead/lag time for the air ﬂow. The

recommended adjustment is one half turn and

not more than one full turn.

3. Tighten the nuts together to ﬁx them in the new

position.

3A2494E

Содержание Pro Xp L40T10















































































Результаты поиска

Содержание Pro Xp L40T10

Отзывы:

Похожие инструкции для Pro Xp L40T10

Бренды по названию

Популярные бренды

Graco Pro Xp L40T10, Инструкция - Каталог запасных частей

Результаты поиска

Содержание Pro Xp L40T10

Отзывы:

Похожие инструкции для Pro Xp L40T10

Бренды по названию

Популярные бренды