background image

3

307982

WARNING

INJECTION HAZARD

Spray from the valve, leaks or ruptured components can inject fluid into your body and cause ex-

tremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can

also cause serious injury.

D

Fluid injected into the skin is a serious injury. The injury may look like just a cut, but it is a serious

injury. Get immediate medical attention.

D

Do not point the valve at anyone or at any part of the body.

D

Do not put your hand or fingers over the valve tip.

D

Do not stop or deflect leaks with your hand, body, glove or rag.

D

Do not “blow back” fluid; this is not an air spray system.

D

Always have the tip guard and the trigger guard on the valve when spraying.

D

Be sure the valve trigger safety operates before dispensing.

D

Lock the valve trigger safety when you stop dispensing.

D

Follow the

Pressure Relief Procedure

on page 8 if the spray tip clogs and before cleaning,

checking or servicing the equipment.

D

Tighten all fluid connections before operating the equipment.

D

Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.

Permanently coupled hoses cannot be repaired; replace the entire hose.

MOVING PARTS HAZARD

Moving parts, such as the pump’s priming piston, can pinch or amputate your fingers.

D

Keep clear of all moving parts when starting or operating the pump.

D

Keep hands and fingers away from the priming piston during operation and whenever the pump is

charged with air.

D

Before checking or servicing the equipment, follow the

Pressure Relief Procedure

on page 8 to

prevent the equipment from starting unexpectedly.

Содержание Power-Flo Bulldog



























Отзывы: