background image

Setup 

12

3A2960A

Setup

Entering SETUP MODE

1.

Press both the UP and DOWN ARROW buttons 
together for three seconds.

NOTE:

 If a button is not pushed for 1 minute, the control-

ler returns to the start of an OFF cycle. 

Programming ON Duration

on:Pr, on:CY

 or 

on:ti

 appears on 

the display identifying the function 
you are programming. 

The LED below the related symbol 
on the controller label also indi-
cates the function.

NOTE:

 Selection 

on:Pr, on:CY

 or 

on:ti

 designates the way the 

pump run time is controlled: 

on:Pr

 = Pressure Control, 

reaching a specific pressure 
threshold measured by an 
external pressure switch

on:CY

 = Cycle Control, com-

pleting a specific number of 
cycles of an external 
prox/cycle switch

on:ti

 = Time Control, a spe-

cific duration of time elapses

Pressure Mode (on:Pr) ON Setup

1.

Use the UP or DOWN ARROW to 
cycle through the 

on:Pr, on:CY

 or 

on:ti 

on the display. 

2.

 When 

on:Pr 

displays, press the 

ENTER button to lock in the selec-
tion.

3.

Pressure control is an ON / OFF 
selection only. Not additional pro-
gramming is required.

Cycle Mode (on:CY) ON Setup

1.

Use the UP or DOWN ARROW to 
cycle through the 

on:Pr, on:CY

 or 

on:ti 

on the display. 

2.

When 

on:CY

 is displayed, press 

ENTER to lock in the selection.

The first number displayed after the 

on:CY

 is entered, blinks, indicating the device is ready 

to program the number of cycles.

3.

Program the cycles by pressing the UP or DOWN 
ARROW to move up or down through the numbers 
0-9.

4.

When the correct first digit is displayed, press the 
ENTER button to lock in the selection

The cursor automatically moves to the second number 
field and flashes.

NOTE:

 The cycle is a 2-digit number. A leading zero (0) 

must be entered in the first field if the number of cycles 
is fewer than 10.

5.

Use the UP or DOWN ARROW to scroll through the 
numerals 0-9 until the desired number appears in 
the second cycle number field.

6.

Press the ENTER button to lock in the selection.

Time Control (on:ti) ON Setup

1.

Use the UP or DOWN ARROW to 
cycle through the 

on:Pr, on:CY

 or 

on:ti 

on the display. 

P: Pressure

C: Cycle

T: Time

Содержание GLC 2200



















Отзывы: