Graco FLOW METERS S3000 Скачать руководство пользователя | Manualshive

Страница: 8 / 24

background image

Installation

8

308778Y

Intrinsically Safe Installation
Requirements

See F

IG

. 2.

1.

The non-intrinsically safe terminals must not be con-
nected to any device which uses or generates more
than 250 Vrms or dc unless it has been determined
that the voltage has been adequately isolated.

2.

The installation must meet the requirements of the
National Electric Code, Canadian Electrical Code
Part I, NFPA 70, Article 504 Resp., Article 505 and
ANSI/ISA 12.06.01.

3.

Multiple earthing of components is allowed only if
high integrity equipotential system is realized
between the points of bonding.

4.

Do not operate system with safety barrier cover
removed.

5.

For ATEX, install per EN 60079-14 and applicable
local and national codes.

6.

Cable used to connect sensor and safety barrier
must take capacitance and inductance into account.
The maximum capacitance of the barrier is to be
greater than the cable capacitance plus the sensor
capacitance (Ci). The maximum inductance of the
barrier is to be greater than the cable inductance
plus the sensor inductance (Li).

Find cable capacitance and inductance by:

a.

Using the most exacting electrical parameters
provided by the cable manufacturer.

b.

Using the electrical parameters determined by
measurement of a sample.

7.

Product meets 500 Vac isolation test between the
intrinsically safe circuits and earth ground.

F

IG

. 2.

Intrinsically Safe Installation

NON-HAZARDOUS LOCATION ONLY

HAZARDOUS (CLASSIFIED) LOCATION

CLASS I, DIV I, GROUP D, T3 (US AND CANADA)
CLASS I, ZONE I GROUP IIA T3 (ATEX ONLY)
TA = 0°C TO 60°C

Safety

Barrier

Flow Meter Body

G3000
G3000HR
G250
G250HR
S3000
G3000A

250 VAC Maximum

Supply Voltage

Power 10-30 Vdc (Red), Ref. to Common

Sensor - 24W650

24W651

Ground

(Grounded thru meter

mounting bracket to

system ground.)

NOTE:

See

Intrinsically Safe Installation Requirements

above.

WARNING:

Substitution of components may impair intrinsic safety. For installation,

maintenance or operation instructions, see instruction manual.

ADVERTISSEMENT:

La substitution de composants peut compromettre la securite

intrinseque.

ATEX CERTIFICATE #ITS12ATEX27565X

SYSTEM ASSEMBLY CERTIFICATE

Ground

System

Common (Black)

Signal 0-30 Vdc (White), Ref. to Common
Cable Shield

Sensor Entity Parameters
(per barrier channel):
Ui/Umax = 30 Vdc
Ii/Imax = 110 mA
Ci = 0.4 microFarads
Li = 0.01 mH
Pi = 0.8 W

24M600
Control Drawing

«
...
6
7
8
9
10
...
»

Содержание FLOW METERS S3000

























Отзывы:

Нет отзывов

Похожие инструкции для FLOW METERS S3000

Бренд: Oceanic Страницы: 17

IEM-100 Beltpack

Бренд: DAPAudio Страницы: 19

Бренд: Gardner Bender Страницы: 4

Бренд: GAPS Страницы: 36

Бренд: yellow jacket Страницы: 26

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 99

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: WalkLAB Страницы: 16

Бренд: MULTISPAN Страницы: 2

SoundTrack LxT N/Forcer

Бренд: Larson Davis Страницы: 12

Бренд: Mark-10 Страницы: 26

Frontline 802.11

Бренд: Teledyne Lecroy Страницы: 223

Бренд: SecureAlert, Inc. Страницы: 7

Бренд: GANN Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды