![background image](http://html1.mh-extra.com/html/graco/endure/endure_owners-manual_2250150007.webp)
12
11
Now you can strap your child into the seat. Make sure the
seat belt has not become twisted. Also check that the
cover is not impeding the movement or fit of the seat belt
webbing in any way. Ensure rigid and plastic parts of child
restraint are not liable to become trapped by a movable
vehicle seat or vehicle doors.
To release your child restraint follow the above instructions
in reverse order.
Fastening the Harness
Slot the two metal sections of the buckle connectors together.
19
-1
Slot the two buckle connectors into the slot in the top of the
buckle until they “click” into place.
19
-2
Always check the harness is correctly locked by pulling the
shoulder straps upwards.
To release the harness, press the red button on the buckle
downwards.
Tightening the Harness
Pull the shoulder straps upwards to remove the slack from the
lap sections of the harness.
20
-1
Pull chest pads down as far as they can go.
20
-2
Now pull the adjuster strap until the harness is fully tightened.
20
-3
The harness should be adjusted as tightly as possible
without causing discomfort to your child.
Ensure that the lap strap portion of the harness is located as
low as possible towards the thighs-not round the tummy.
A loose harness can be dangerous. Check the harness
adjustment and tighten each time the child is placed in the
seat.
Slackening the Harness
The harness is slackened by pressing the lever (under the seat
cover) on the front of the seat.
21
-1
Grip the two shoulder straps with one hand. Then press down
on the lever underneath the softgoods as you pull the shoulder
straps towards you to loosen the harness.
21
-2
Take care when adjusting the shoulder straps that you do
not trap the harness adjuster straps as you press the lever
down.
TAKE CARE - Check harness straps are not twisted.
15-36 kg
Removing the Safety Harness Shoulder Straps
22
Firstly, loosen the harness.
23
From the rear of the seat find the harness connector.
23
-1
Slide both the harness straps off the harness connector at
the back of the backrest.
23
-2
From the front of the seat,
pull the straps through the slots in the seat backrest and
fabric cover.
Removing the Safety Harness Lap
Straps and Crotch Strap
24
From underneath the seat, locate the three webbing
retainer buckles. Turn the buckles on their narrowest end
and feed them, complete with webbing straps, through the
slots in the base of the seat, then through the slots in the
fabric cover. The lap straps and crotch strap can then be
removed completely from the seat.
Store the newborn liner, chest pads, crotch pads and
harness straps in a safe place.
Adjusting the Headrest
According to the child’s height, the headrest can be adjusted up
or down.
25
Put one hand on the backrest. Pull the button in the
headrest with your other hand.
25
-1
Move the headrest up or down as required ensuring your
child’s head is centred on the headrest.
25
-2
Check to make sure it is clicked into one of the six height
positions by pulling up on head support.
The red seat belt guides must be level with, or just above,
the shoulders, as shown by the dotted line.
26
Using the correct headrest height, as shown in
26
.
Fitting the child restraint using
the Adult Seat Belt
IMPORTANT: Before fitting the seat remove the shoulder
straps, crotch strap and lap strap. (See
22
to
24
)
27
Place the child restraint onto the vehicle’s seat. Ensure that
the backrest of the seat is pushed firmly against the backrest
of the vehicle’s seat. Place the child in the child restraint.