Graco 26C265 Скачать руководство пользователя страница 2

Страница: 2 / 40

311053L

Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Ventilate Spray Booth  . . . . . . . . . . . . . . . . . . . . .  5
Configure Gun and Manifold  . . . . . . . . . . . . . . . .  5
Install Air Fittings . . . . . . . . . . . . . . . . . . . . . . . . .  6
Ground System  . . . . . . . . . . . . . . . . . . . . . . . . . .  6
Mount Gun   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  7

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Air Line and Accessory Recommendations   . . . .  8
Fluid Line and Accessory Recommendations  . . .  8
Flush Spray Gun  . . . . . . . . . . . . . . . . . . . . . . . .  10
Install Spray Tip   . . . . . . . . . . . . . . . . . . . . . . . .  10
Adjust Spray Pattern  . . . . . . . . . . . . . . . . . . . . .  11
Adjust a Streaming Tip  . . . . . . . . . . . . . . . . . . .  11

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Pressure Relief Procedure . . . . . . . . . . . . . . . . 12
Apply the Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 12

Daily Gun Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

General System Maintenance . . . . . . . . . . . . . .  14
Daily Cleaning Procedure  . . . . . . . . . . . . . . . . .  14
Clean Spray Tips and Clear Clogs  . . . . . . . . . .  14
Daily Flushing Procedure  . . . . . . . . . . . . . . . . .  15

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 16

General Troubleshooting . . . . . . . . . . . . . . . . . . 16
Spray Pattern Troubleshooting . . . . . . . . . . . . . 18

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Model 26C624  . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Model 26C625  . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Model 288048  . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Model 288554  . . . . . . . . . . . . . . . . . . . . . . . . . . 27

GG0 Series Tip Selection Charts . . . . . . . . . . . . . 30

XHD RAC Switch Tip Selection Charts . . . . . . . . 31

Sealer Application Tip and

Air Cap Selection Charts . . . . . . . . . . . . . . . . 32

Shower Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Streaming Tips . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Single Orifice Fan Pattern Spray Tips . . . . . . . . 32

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

288048, 288554 . . . . . . . . . . . . . . . . . . . . . . . . . 34
26C624 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
26C625 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Mounting Hole Layout . . . . . . . . . . . . . . . . . . . . . . 37

End of Product Life . . . . . . . . . . . . . . . . . . . . . . . . 38

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 40

Содержание 26C265









































Результаты поиска

Содержание 26C265

Отзывы:

Graco 26C265, Инструкция по эксплуатации, Страница: 2 / 40

Результаты поиска

Содержание 26C265

Отзывы: