Graco 26C265 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 40

Graco 26C265 Скачать руководство пользователя страница 16

Troubleshooting

16

311053L

Troubleshooting

NOTE:

Check all possible remedies in the

troubleshooting charts before disassembling the gun.

NOTE:

Some improper patterns are caused by the

improper balance between air and fluid. Refer to

Pattern Troubleshooting

, page 18.

General Troubleshooting

Problem

Cause

Solution

Fluid leakage through venting
holes.

Worn o-rings or packings on needle
assembly (12).

Replace o-rings or needle assembly.

Air leakage through venting
hole.

Worn o-ring (23).

Check and replace as needed.

Air leakage from back of gun.

Worn o-rings (22, 23).

Replace o-rings.

Fluid leakage from front of gun. Fluid needle (12) is dirty, worn, or

damaged

Clean or replace fluid needle.

Dirty or worn seat (10, 41).

Clean or replace the seat (10, 41) and
gasket (11). The gasket must be replaced
whenever you remove the seat from the
gun.

Spray tip seal is leaking.

Tighten nut (7) or replace spray tip gasket
(8).

Seat (10, 41) is insufficiently
tightened or gasket (11) is missing
or worn from multiple uses.

Tighten seat (10, 41) and replace gasket
(11). The gasket must be replaced
whenever you remove the seat from the
gun.

«
...
14
15
16
17
18
...
»

Содержание 26C265









































Отзывы:

Нет отзывов