manualshive.com logo in svg

Graco 26C265, Инструкция по эксплуатации, Страница: 33 / 40

Поделиться
Скачать
Graco 26C265 Скачать руководство пользователя страница 33

Accessories

311053L

33

Accessories

Gun Manifolds

Order separately; not included with gun.
(See 

Parts List - 288048 and 288554

, page 28.)

Part No. 241161

North America Manifold

Part No. 241162

International Manifold

Part No. 244930

High Flow Ambient or Temperature Conditioned 
Manifold for streaming or spraying.

Grounding Clamp and Wire 222011

High Pressure Ball Valves, Fluoroelastomer 
Seals

5000 psi (34 MPa, 345 bar) Maximum Working Pressure

Can be used as fluid drain valve.

Bleed-type Master Air Valve

250 psi (1.7 MPa, 17 bar) Maximum Working Pressure

 

Relieves air trapped in the air line between the pump air 
inlet and this valve when closed.

Gasket Filter

Gasket filter 288201, package of 10. Small filter can be 
installed in the inlet gasket (3) for added filtration.

Tube Fittings for Air or Water

250 psi (1.7 MPa, 17 bar) Maximum Working Pressure

160° F (71° C) temperature rating

Filter Kit

Consists of just the filter element
Filter 60 mesh, qty. 25 - 238564
Filter 60 mesh, qty. 3 - 238563
Filter 100 mesh, qty. 25 - 238562
Filter 100 mesh, qty. 3 - 238561

Brush 101892

For cleaning the gun.

In-line Fluid Filter

6150 psi (42.4 MPa, 424 bar) Maximum Working 
Pressure Fits onto the gun fluid connector. 1/4-18 npsm

Needle/Diffuser Options

Needles must be used only with the specified seat to 
guarantee proper seating and life.

•

Standard viscosity/standard flow

-

Fluid Needle 24B916, 3/16 in. carbide ball

-

Seat 288196

•

Acid catalyzed materials/very low viscosity 
materials

-

Fluid Needle 241468, 3/16 in. plastic ball

-

Seat 288196

Temperature Sensor and Cable

For temperature conditioned manifold

XHD RAC Guard, SST XHD003

Part

Description

210657 1/2 npt(m)
210658 3/8 npt(m)
210659 3/8 x1/4 npt(m)

Part

Description

107141 3/4 npt(m x f) inlet and outlet
107142 1/2 npt(m x f) inlet and outlet

Part

Length

104172

1/8 npt(m) x 1/4 OD tube

597151

1/8 npt(m) x 1/4 OD tube, 90° elbow (swivel)

Part

Description

210500

100 mesh. Includes the parts shown below. 
Consists of filter element 205264.

26C633

60 mesh. Consists of filter element 205265.

Part

Length

198457 RTD Sensor, 100 ohm, 1/8 npt(m) with 3 pin 

Picofast connector

198458 RTD cable, 6 ft. (1.83 m) Flex cable to St. 

Clair connector

210501

168517

205264 (100 mesh)

}

or 205265 (60 mesh)

Содержание 26C265









































Отзывы:

Нет отзывов