manualshive.com logo in svg

Graco 26C265, Инструкция по эксплуатации, Страница: 39 / 40

Поделиться
Скачать
Graco 26C265 Скачать руководство пользователя страница 39

Technical Data

311053L

39

Technical Data

Triggering Speed

These values apply to a new gun with a 6 ft (1.8 m), 1/4 in. (6.3 mm) OD cylinder air line and a 0.019 in. tip. These 
values will vary slightly with use and with variations in equipment.

Sound Pressure Levels (dBa)

Sound pressure measured 3.28 ft (1 m) from equipment.

Sound Power Levels (dBa)

Sound power measured per ISO-9641-2.

Spray Guns 288048 and 288554

US

Metric

Maximum working fluid pressure

5000 psi 

36 MPa, 360 bar

Minimum air cylinder actuation pressure at 4000 psi

70 psi

0.49 MPa, 4.9 bar

Minimum air cylinder actuation pressure at 5000 psi

75 psi

0.51 MPa, 5.1bar

Maximum working fluid temperature

Paint applications

120 °F

49 °C

Non-flammable sealant applications

140 °F

60 °C

Weight

1.17 lb

529 g

Wetted Parts

Stainless Steel, Carbide, Ultra High Molecular Weight Polyethylene, 
Acetal, PEEK, Chemically Resistant Fluoroelastomer, PTFE

Spray Gun 26C624

Maximum working fluid pressure

5000 psi 

36 MPa, 360 bar

Minimum air cylinder actuation pressure at 4000 psi

70 psi

0.49 MPa, 4.9 bar

Minimum air cylinder actuation pressure at 5000 psi

75 psi

0.51 MPa, 5.1 bar

Maximum working fluid temperature

Paint applications

160 °F

71 °C

Weight

1.24 lb

563 g

Wetted Parts

Stainless Steel, Carbide, Ultra High Molecular Weight Polyethylene, 
Acetal, PEEK, Chemically Resistant Fluoroelastomer, PTFE, Nylon

Spray Gun 26C625

Maximum working fluid pressure

7250 psi 

50 MPa, 500 bar

Minimum air cylinder actuation pressure at 7250 psi

95 psi

0.65 MPa, 6.5 bar

Maximum working fluid temperature

Paint applications

160 °F

71 °C

Weight

1.24 lb

563 g

Wetted Parts

Stainless Steel, Carbide, Ultra High Molecular Weight Polyethylene, 
Acetal, PEEK, Chemically Resistant Fluoroelastomer, PTFE, Nylon

Cylinder Air Pressure 

psi (kPa, bar)

Fluid Pressure 

psi (kPa, bar)

msec to fully open

msec to fully close

70 (0.49, 4.9)

600 (4.2, 42)

51

72

70 (0.49, 4.9)

1800 (12.4, 124)

56

73

70 (0.49, 4.9)

4000 (28, 280)

69

73

Input Fluid Pressures

1500 psi (10.5 MPa, 105 bar)

4000 psi (28 MPa, 276 bar)

79.0 dB(A)

86.6 dB(A)

Input Fluid Pressures

1500 psi (10.5 MPa, 105 bar)

4000 psi (28 MPa, 276 bar)

75.7 dB(A)

86.3 dB(A)

Содержание 26C265









































Отзывы:

Нет отзывов