Graco 25T991 Скачать руководство пользователя страница 10

Страница: 10 / 52

Installation

3A8476A

Cable Connections

NOTE:

Cables and hoses are attached only after SST

Switch 3D Gun is bolted to robot.

Connect cable (1001) for all SST Switch 3D Gun

models, and (1003) for SST Switch 3D guns with

sensors. Then connect other end of the cables by

making the appropriate connections to the robot’s

control cabinet. See F

. 6.

See the

Models

table page 3, for the cable type needed

for your SST Switch 3D Gun mode.

Hose Connections

The air supply is connected to the SST Switch 3D Gun

with an 8 mm polyurethane hose to the elbow swivel

fitting (512) on the side of the swivel housing (511).

Customer must install air bleed valve between air supply

and SST Switch 3D Gun connection. See F

. 7.

The material supply hose connects to the SST Switch

3D gun using a customer supplied fitting. The inlet

thread is 1/2 In. BSPP. See F

. 7.

PCF Installation

NOTE:

The following installation is for SST Switch 3D

Guns that use a Precision Continuous Flow Unit (PCF).
See

PCF to 3D Gun Cable Kit 25U441

on page 37 for

parts.

1. Remove the PCF cover (A).

2. Disconnect the dispense valve air solenoid cable

from FCM port 1(B). Secure the loose end of the
cable to the PCF fluid mounting plate (C).

3. Disconnect the regulator air line (D) from the

incoming air wye fitting (E).

4. Disconnect the incoming air wye fitting (D) from the

incoming air elbow fitting (F). Secure the incoming
air wye fitting to the PCF fluid mounting plate (C).
See F

. 8 page

11.

. 5

. 6

NOTICE

Only use air fittings that are rated at a temperature
equal to or higher than the operating temperature of
the fluid dispensing system. Lower rated air fittings
could melt and cause damage to the SST Switch 3D
Gun.

801

902

707

901

105

Connect to robot control cabinet

(not shown).

1001 and 1003 if

equipped with

sensors

. 7

511

Customer supplied

material hose.

Customer

supplied 8 mm

air hose.

Customer supplied

bleed valve

512

Содержание 25T991





















































Результаты поиска

Содержание 25T991

Отзывы:

Похожие инструкции для 25T991

Бренды по названию

Популярные бренды

Graco 25T991, Инструкция - Каталог запасных частей

Результаты поиска

Содержание 25T991

Отзывы:

Похожие инструкции для 25T991

Бренды по названию

Популярные бренды