background image

 

9

INSTALLATION & PREPARATION 
INSTRUCTIONS

Engine Fuel Tank

Review “Fire & Ventilation Precautions” pg. 4, before 
fueling.

Locate the Safety Decals on your unit and heed their 
warnings. 

A minimum of 86 octane fuel is recommended for use 
with this unit.  Do not mix oil with gasoline.

Purchase fuel in quantities that may be used within 30 
days.  Use of clean, fresh lead free gasoline is recom-
mended.  Leaded gasoline may be used if lead-free is 
unavailable.  Do not use gasoline containing methanol 
or alcohol.

Check the engine oil level before starting the engine. 
(See engine manual.)

Fill the fuel tank according to accompanying engine 
manual instructions.

Occasional carburetor and choke adjustments will be 
necessary for the engine.  Refer to the engine manual 
supplied with this unit for proper adjustment proce-
dures. 

Review the engine manual accompanying this pressure 
washer for correct engine start-up and maintenance 
procedures.

Nozzle Review

Various nozzles may be quick-connected into the end 
of the wand to change the spray pattern or use the 
detergent feature.  When using Quick Connects (Q.C.), 
be certain the connection is securely locked.  If not, 
the high pressure water may shoot the nozzle from the 
wand, causing severe injury or serious damage.  

To determine spray fan, refer to the actual number 

stamped on the nozzle.  The first two digits indicate the 

spray fan in degrees, i.e.; 0=0°, 15=15°, 25=25°, 40 = 

40°, 65=detergent/low pressure, rotoblast nozzle.

The 0° nozzle  (RED):  This is a blasting nozzle.  It deliv

-

ers a very concentrated stream of water. Be cautious 
when using the straight narrow stream.  It is not recom-
mended for use on painted or wood surfaces, or items 

attached with adhesive backings.  Uses:  Removing 

weeds from sidewalk cracks, stubborn stains from con-
crete, masonry, aluminum and steel, caked mud from  
equipment, and cleaning lawn mower undersides.

The 15° nozzle  (YELLOW):  This is a chiseling nozzle.  

The spray should be directed at a 45° angle to the 
surface and used like a scraper to remove paint, grease 

and dirt.  Uses:  Surface preparation (removing mildew 

stains and paint chips).

The 25° nozzle  (GREEN):  This is a flushing nozzle.  
This pattern is best suited for flushing dirt, mud, and 
grime.  Uses:  Wet sweeping leaves from walks, curbs 
and driveways, cleaning stable floors, washing swim

-

ming pool bottoms, degreasing engines.

The 40° nozzle (WHITE): This is a wash nozzle. This 

wide spray pattern disperses the water pressure over a 
large area and is recommended for moderate washing. 

Uses: Washing down aluminum siding, cleaning win

-

dows, washing vehicles, spraying sidewalks, driveways 
and patios. (not available for Model 2525)

The 65° nozzle  (BLACK):  This is a low pressure de

-

tergent application nozzle.  This broad spray pattern 
distributes solution over vast areas under low pressure.  

Uses: Detergent application, misting or rinsing.

The Rotoblast nozzle: Rotating nozzles increase your 

cleaning power and decrease your cleaning time. 
They offer 0° spray impact with 25° coverage. Nozzles 

include filter with quick connect and offer heavy-duty 
components for long life and reliability. Uses: Sidewalks, 

driveways, track vehicles, muddy areas, old peeling 
paints and concrete surfaces.



Содержание 2525DD











































Отзывы: