background image

10 

 

 

 

 

INSTALLATION & PREPARATION 
INSTRUCTIONS

Nozzle Connection

Be certain the trigger gun is locked in the “OFF” posi-
tion.  

The nozzle assembly should be disconnected from 

the gun/wand assembly at this time by retracting the 
locking ring on the quick-connect fitting to remove the 

nozzle. 

Water Supply

Select a water supply hose which is a quality grade of 

garden hose measuring at least 3/4” ID and no longer 

than 50 feet.

Check the water inlet strainer to ensure it is clean and 
free of any obstructions.  Periodic cleaning of the water 
strainer will help prevent pump problems.  

NOTICE

As a strainer becomes obstructed, it restricts proper 

flow of water to the pump. This can result in cavita

-

tions which will cause premature failure of pump 
packings.  

1.  Using a screw driver, remove the screen from the water 

inlet.

2.  Clean or replace if necessary.

Connect the hoses.

1.  Connect one end of the water supply hose to the water 

inlet of the unit.  

2.  Connect the other end of the hose to your pressurized 

water supply.

Note: 

Do not use a non-pressurized water supply (i.e. 

from a pond or well) with this unit.

3.  Connect the high pressure discharge hose to the water 

outlet of the unit. 

4.  Securely  connect  the  other  end  of  the  hose  to  the 

gun assembly.  (A wrench may be required on some 
models.)

5.  Connect the wand assembly to the gun/hose assembly.

Follow the incoming water requirements listed below:

1.  Water pressure must be a minimum of 25 pounds per 

square inch (PSI) and a maximum of 125 PSI.  (A typical 
outdoor faucet will generally supply this PSI if turned 
completely “ON”.) 

2.  Incoming GPM must be  approximately one gallon more 

than the outgoing GPM stated on the pressure washer 
nameplate.  (You can check GPM by timing how long 

it takes to fill a 5 gallon container.)

  

NOTICE

Incoming water temperature must not exceed 125°F 
for Model 2525, and 145°F for other models. Exces-
sive pump damage may result if the water tempera-
ture exceeds this acceptable level.

NOTICE

Damage to the equipment could occur. Never allow 
the unit to operate without the incoming water line 
attached and the water supply completely turned on.

Содержание 2525DD











































Отзывы: